參數資料
型號： GMS81C2120K
廠商： HYNIX SEMICONDUCTOR INC
元件分類： 微控制器/微處理器
英文描述： HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS
中文描述： 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
封裝： SDIP-42
文件頁數： 69/93頁
文件大?。?/td> 853K
代理商： GMS81C2120K
GMS81C1404/GMS81C1408
June. 2001 Ver 1.2
67
Figure 19-3 Timing of STOP Mode Release by RESET
19.2 STOP Mode using Internal RCWDT
In the STOP mode using Internal RC-Oscillated Watchdog
Timer, the on-chip oscillator is stopped. But internal RC
oscillation circuit is oscillated in this mode. The on-chip
RAM and Control registers are held. The port pins out the
values held by their respective port data register, port di-
rection registers.
The Internal RC-Oscillated Watchdog Timer mode is
activated by execution of STOP instruction after set-
ting the bit RCWDT of CKCTLR to “1”. ( This register
should be written by byte operation. If this register is
set by bit manipulation instruction, for example “set1”
or “clr1” instruction, it may be undesired operation )
Note:
After STOP instruction, at least two or more NOP in-
struction should be written
Ex)
LDM WDTR
,#1111_1111B
LDM CKCTLR
,#00
1
0_1110B
STOP
NOP
NOP
Release the STOP mode using internal RCWDT
The exit from STOP mode using Internal RC-Oscillated
Watchdog Timer is hardware reset or external interrupt.
Reset re-defines all the Control registers but does not
change the on-chip RAM. External interrupts allow both
on-chip RAM and Control registers to retain their values.
If I-flag = 1, the normal interrupt response takes place. In
this case, if the bit WDTON of CKCTLR is set to “0” and
the bit WDTE of IENH is set to “1”, the device will exe-
cute the watchdog timer interrupt service routine.(Figure
19-4 ) However, if the bit WDTON of CKCTLR is set to
“1”, the device will generate the internal RESET signal
and execute the reset processing. (Figure 19-5 )
If I-flag = 0, the chip will resume execution starting with
the instruction following the STOP instruction. It will not
vector to interrupt service routine.( refer to Figure 19-1 )
When exit from STOP mode using Internal RC-Oscillated
Watchdog Timer by external interrupt, the oscillation sta-
bilization time is required to normal operation. Figure 19-
4 shows the timing diagram. When release the Internal
RC-Oscillated Watchdog Timer mode, the basic interval
timer is activated on wake-up. It is increased from 00
H
un-
til FF
H
. The count overflow is set to start normal opera-
tion. Therefore, before STOP instruction, user must be set
its relevant prescaler divide ratio to have long enough time
(more than 20msec). This guarantees that oscillator has
started and stabilized.
By reset, exit from STOP mode using internal RC-Oscillat-
ed Watchdog Timer is shown in Figure 19-5 .
~
STOP Mode
Time can not be control by software
Oscillator
(X
IN
pin)
~
~
~
STOP Instruction Execution
Stabilizing Time
t
ST
= 64mS @4MHz
Internal
Clock
Internal
RESET
~
~
~
~
~
RESET
相關PDF資料
PDF描述
GMS81C2120Q HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81C5108-UDXXX MICROCONTROLLER|8-BIT|CMOS|QFP|80PIN|PLASTIC
GMS81C3004 POWER SUPPLY FOR SERVSELEECT ACCESS MODULE
GMS81C4040 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81C7008 HYNIX SEMICONDUCTOR INC. 8-BIT SINGLE-CHIP MICROCONTROLLERS
相關代理商/技術參數
參數描述
GMS81C2120Q 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:HYNIX SEMICONDUCTOR 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81C3004 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:CMOS SINGLE-CHIP 8-BIT MICROCONTROLLER WITH LCD DRIVER
GMS81C4040 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81C50 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE CHIP MICROCONTROLLERS
GMS81C5016 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE CHIP MICROCONTROLLERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*