參數資料
型號： FT2232HQ-TRAY
廠商： Future Technology Devices International Ltd
元件分類： 總線控制器
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, PQCC64
封裝： LEAD FREE, QFN-64
文件頁數： 5/63頁
文件大小： 1598K
代理商： FT2232HQ-TRAY
Copyright 2010 Future Technology Devices International Limited
13
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 2.10
Clearance No.: FTDI#77
3.4.3 FT2232H pins used in an FT245 Style Asynchronous FIFO Interface
The FT2232H channel A or channel B can be configured as a FT245 asynchronous FIFO interface. When
configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.6. To
enter this mode the external EEPROM must be set to make port A or B or both 245 mode. In this mode,
data is written or read on the falling edge of the RD# or WR# signals.
Channel A
Pin No.
Channel B
Pin No.
Name
Type
FT245 Configuration Description
24,23,22,21,
19,18,17,16
46,45,44,43,
41,40,39,38
Channel A =
ADBUS[7:0]
Channel B =
BDBUS[7:0]
I/O
D7 to D0 bidirectional FIFO data. This bus is normally input
unless RD# is low.
26
48
RXF#
OUTPUT
When high, do not read data from the FIFO. When low,
there is data available in the FIFO which can be read by
driving RD# low. When RD# goes high again RXF# will
always go high and only become low again if there is
another byte to read. During reset this signal pin is tri-
state, but pulled up to VCCIO via an internal 200kΩ
resistor.
27
52
TXE#
OUTPUT
When high, do not write data into the FIFO. When low, data
can be written into the FIFO by strobing WR# high, then
low. During reset this signal pin is tri-state, but pulled up to
VCCIO via an internal 200kΩ resistor.
28
53
RD#
INPUT
Enables the current FIFO data byte to be driven onto
D0...D7 when RD# goes low. Fetches the next FIFO data
byte (if available) from the receive FIFO buffer when RD#
goes high.
29
54
WR#
INPUT
Writes the data byte on the D0...D7 pins into the transmit
FIFO buffer when WR# goes from high to low.
30
55
SIWU
INPUT
The Send Immediate / WakeUp signal combines two
functions on a single pin. If USB is in suspend mode
(PWREN# = 1) and remote wakeup is enabled in the
EEPROM , strobing this pin low will cause the device to
request a resume on the USB Bus. Normally, this can be
used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is
strobed low any data in the device TX buffer will be sent out
over USB on the next Bulk-IN request from the drivers
regardless of the pending packet size. This can be used to
optimize USB transfer speed for some applications. Tie this
pin to VCCIO if not used. (Also see note 1, 2, 3 in section
Table 3.6 Channel A and Channel B FT245 Style Asynchronous FIFO Configured Pin Descriptions
相關PDF資料
PDF描述
FT2232HL-TRAY
FT245BL
FT245BQ
FT245BM
FTL-1419-3D FIBER OPTIC TRANSCEIVER, 1290-1340nm, 1250Mbps(Tx), 1250Mbps(Rx), PANEL MOUNT
相關代理商/技術參數
參數描述
FT2232L 功能描述:UART 接口集成電路 Obsolete See FT2232D-REEL RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
FT2232L/TR 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB UART/FIFO SMD 2232 LQFP48
FT22L 功能描述:OVEN FOOD PROBE RoHS:是 類別:測試設備 >> 測試引線 - 熱電偶，溫度探頭 系列:FT 標準包裝:1 系列:6543 類型:J 型熱電偶 使用:液體，半固體 尖端 - 類型:防浸漬 / 穿透式，圓頭 插頭類型:超微型（熱電偶插頭） 探針溫度范圍:-40 ~ 2000°F（-40 ~ 1093°C） 線纜長度:- 線纜絕緣:- 插頭顏色:黑 探針長度:12.000"（304.80mm） 探針材料:-
FT230A 制造商:Black Box Corporation 功能描述:HAND STRIPPER
FT230X 制造商:FTDI 制造商全稱:FTDI 功能描述:USB to serial UART interface with optimised pin count for smaller PCB designs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*