- 您現在的位置：買賣IC網 > PDF目錄11822 > FT2232HL-TRAY (FTDI, Future Technology Devices International Ltd)IC USB HS DUAL UART/FIFO 64-LQFP PDF資料下載
參數資料
| 型號： | FT2232HL-TRAY |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 37/67頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB HS DUAL UART/FIFO 64-LQFP |
| 標準包裝： | 160 |
| 系列： | USBmadeEZ-FIFO，F(xiàn)T-X，X-Chip |
| 特點： | USB 至 UART 和（或）FIFO、SPI、I2C、JTAG |
| 通道數： | 2，DUART |
| FIFO's： | 4096 字節 |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 3 V ~ 3.6 V |
| 帶并行端口： | 是 |
| 帶自動流量控制功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP |
| 包裝： | 托盤 |
| 其它名稱： | FT2232HL - TRAY |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁
Copyright 2012 Future Technology Devices International Limited
42
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
4.10 Synchronous and Asynchronous Bit-Bang Interface Mode
Description
The FT2232H channel A or channel B can be configured as a bit-bang interface. There are two types of
bit-bang modes: synchronous and asynchronous.
Asynchronous Bit-Bang Mode
Asynchronous Bit-Bang mode is the same as BM-style Bit-Bang mode, except that the internal RD# and
WR# strobes (RDSTB# and WRSTB#) are now brought out of the device to allow external logic to be
clocked by accesses to the bit-bang IO bus.
On either or both channels any data written to the device in the normal manner will be self clocked onto
the data pins (those which have been configured as outputs). Each pin can be independently set as an
input or an output. The rate that the data is clocked out at is controlled by the baud rate generator.
For the data to change there has to be new data written, and the baud rate clock has to tick. If no new
data is written to the channel, the pins will hold the last value written.
Synchronous Bit-Bang Mode
The synchronous Bit-Bang mode will only update the output parallel port pins whenever data is sent from
the USB interface to the parallel interface. When this is done, the WRSTB# will activate to indicate that
the data has been read from the USB Rx FIFO buffer and written out on the pins. Data can only be
received from the parallel pins (to the USB Tx FIFO interface) when the parallel interface has been
written to.
With Synchronous Bit-Bang mode data will only be sent out by the FT2232H if there is space in the
FT2232H USB TXFIFO for data to be read from the parallel interface pins. This Synchronous Bit-Bang
mode will read the data bus parallel I/O pins first, before it transmits data from the USB RxFIFO. It is
therefore 1 byte behind the output, and so to read the inputs for the byte that you have just sent,
another byte must be sent.
For example :-
(1) Pins start at 0xFF
Send 0x55,0xAA
Pins go to 0x55 and then to 0xAA
Data read = 0xFF,0x55
(2) Pins start at 0xFF
Send 0x55,0xAA,0xAA
(repeat the last byte sent)
Pins go to 0x55 and then to 0xAA
Data read = 0xFF,0x55,0xAA
Synchronous Bit-Bang Mode differs from Asynchronous Bit-Bang mode in that the device parallel output
is only read when the parallel output is written to by the USB interface. This makes it easier for the
controlling program to measure the response to a USB output stimulus as the data returned to the USB
interface is synchronous to the output data.
Asynchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 1 will
enable Asynchronous Bit-Bang mode.
Synchronous Bit-Bang mode is enabled using Set Bit Bang Mode driver command. A hex value of 4 will
enable Synchronous Bit-Bang mode.
See application note AN2232-02, “Bit Mode Functions for the FT2232” for more details and
examples of using the bit-bang modes.
An example of the synchronous bi-bang mode timing is shown in Figure 4.19
相關PDF資料 |
PDF描述 |
|---|---|
| SC28L92A1A,512 | IC UART DUAL W/FIFO 44-PLCC |
| VI-B5B-IY | CONVERTER MOD DC/DC 95V 50W |
| D38999/20WD19PC | CONN RCPT 19POS WALL MNT W/PINS |
| ATMEGA169PV-8MCHR | MCU AVR 16KB FLASH 16MHZ 64QFN |
| MS27484T16B8PA | CONN PLUG 8POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT2232HMINIMODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module |
| FT2232H-MINI-MODULE | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED |
| FT2232HQ | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64 |
| FT2232HQ_MINI_ MODULE | 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| FT2232HQ-4000 | 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC |
發布緊急采購，3分鐘左右您將得到回復。