參數資料
型號： FSCQ1565RPVDTU
廠商： FAIRCHILD SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： Green Mode Fairchild Power Switch (FPS⑩)
中文描述： 33.2 A SWITCHING REGULATOR, 22 kHz SWITCHING FREQ-MAX, PZFM5
封裝： TO-3PF, 7PIN
文件頁數： 18/45頁
文件大小： 1379K
代理商： FSCQ1565RPVDTU
18
www.fairchildsemi.com
FSCQ-Series Rev. 1.1.2
F
output, the output voltage may exceed the rated voltage
before the over load protection triggers, resulting in the
breakdown of the devices in the secondary side. In order
to prevent this situation, an over voltage protection
(OVP) circuit is employed. In general, the peak voltage of
the sync signal is proportional to the output voltage and
the FSCQ-Series uses a sync signal instead of directly
monitoring the output voltage. If the sync signal exceeds
12V, an OVP is triggered resulting in a shutdown of
SMPS. In order to avoid undesired triggering of OVP dur-
ing normal operation, the peak voltage of the sync signal
should be designed to be below 12V. This protection is
implemented in the auto restart mode.
4.4 Thermal Shutdown (TSD):
The SenseFET and the
control IC are built in one package. This makes it easy for
the control IC to detect abnormal over temperature of the
SenseFET. When the temperature exceeds approxi-
mately 150
°
C, the thermal shutdown triggers. This pro-
tection is implemented in the latch mode.
5. Soft Start:
The FSCQ-Series has an internal soft-start
circuit that increases PWM comparator’s inverting input
voltage together with the SenseFET current slowly after
it starts up. The typical soft start time is 20ms. The pulse
width to the power switching device is progressively
increased to establish the correct working conditions for
transformers, inductors, and capacitors. Increasing the
pulse width to the power switching device also helps pre-
vent transformer saturation and reduces the stress on
the secondary diode during startup. For a fast build up of
the output voltage, an offset is introduced in the soft-start
reference current.
6. Burst Operation:
In order to minimize the power con-
sumption in the standby mode, the FSCQ-Series
employs burst operation. Once FSCQ-Series enters into
the burst mode, FSCQ-Series allows all output voltages
and effective switching frequency to be reduced. Figure
15 shows the typical feedback circuit for C-TV applica-
tions. In normal operation, the picture on signal is
applied and the transistor Q
1
is turned on, which decou-
ples R
3
, D
z
and D1 from the feedback network. There-
fore, only V
o1
is regulated by the feedback circuit in
normal operation and determined by R
1
and R
2
as:
In the standby mode, the picture ON signal is disabled
and the transistor Q
1
is turned off, which couples R
3
, Dz,
and D
1
to the reference pin of KA431. Then, Vo2 is deter-
mined by the zener diode breakdown voltage. Assuming
that the forward voltage drop of D
1
is 0.7V, V
o2
in standby
mode is approximately given by:
Figure 15. Typical Feedback Circuit to Drop
Output Voltage in Standby Mode
Figure 17 shows the burst mode operation waveforms.
When the picture ON signal is disabled, Q
1
is turned off
and R
3
and Dz are connected to the reference pin of
KA431 through D
1
. Before V
o2
drops to V
o2stby
, the volt-
age on the reference pin of KA431 is higher than 2.5V,
which increases the current through the opto LED. This
pulls down the feedback voltage (V
FB
) of FSCQ-Series
and forces FSCQ-Series to stop switching. If the switch-
ing is disabled longer than 1.4ms, FSCQ-Series enters
into burst operation and the operating current is reduced
from I
OP
to 0.25mA (I
OB
). Since there is no switching, V
o2
decreases until it reaches V
o2stby
. As V
o2
reaches V
o2stby
,
the current through the opto LED decreases allowing the
feedback voltage to rise. When the feedback voltage
reaches 0.4V, FSCQ-Series resumes switching with a
predetermined peak drain current of 0.9A. After burst
switching for 1.4ms, FSCQ-Series stops switching and
checks the feedback voltage. If the feedback voltage is
below 0.4V, FSCQ-Series stops switching until the feed-
back voltage increases to 0.4V. If the feedback voltage is
above 0.4V, FSCQ-Series goes back to the normal oper-
ation.
The output voltage drop circuit can be implemented
alternatively as shown in Figure 16. In the circuit of Fig-
ure 16, the FSCQ-Series goes into burst mode, when
picture off signal is applied to Q1. Then, V
o2
is deter-
mined by the zener diode breakdown voltage. Assuming
that the forward voltage drop of opto LED is 1V, the
approximate value of V
o2
in standby mode is given by:
V
o1norm
2.5
R
--------------------
R
2
+
R
2
=
V
o2stby
V
Z
0.7
2.5
+
+
=
Picture ON
Micom
V
O2
Linear
Regulator
V
O1
(B+)
KA431
R
2
R
1
R
3
R
bias
R
D
R
F
C
F
D
1
Q1
A
C
R
D
Z
V
o2stby
V
Z
1
+
=
相關PDF資料
PDF描述
FSD1000 Combo Fairchild Power Switch (FPS)
FSD200B Green Mode Fairchild Power Switch (FPS)
FSD200BM Green Mode Fairchild Power Switch (FPS)
FSD210B Green Mode Fairchild Power Switch (FPS)
FSD210BM Green Mode Fairchild Power Switch (FPS)
相關代理商/技術參數
參數描述
FSCQ1565RT 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS) for Quasi-Resonant Switching Converter
FSCQ1565RTYDTU 功能描述:開關變換器、穩壓器與控制器 15A/650V QRC Power Switch RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
FSCR502Y 制造商:Panduit Corp 功能描述:Fiber Optic Cable 2Conductors 6.5mm Black
FSCR504Y 制造商:Panduit Corp 功能描述:Fiber Optic Cable 4Conductors 6.5mm Black
FSCR506Y 制造商:Panduit Corp 功能描述:Fiber Optic Cable 6Conductors 6.5mm Black 制造商:Panduit Corp 功能描述:6-FIBER (OM2) MULTIMODE RISER INDOOR/OUT - Cable Rools/Shrink Tubing
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*