- 您現在的位置：買賣IC網 > PDF目錄8941 > FS7145-02G-XTP (ON Semiconductor)IC CLOCK GEN PLL PROG 16SSOP PDF資料下載
參數資料
| 型號： | FS7145-02G-XTP |
| 廠商： | ON Semiconductor |
| 文件頁數： | 17/17頁 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GEN PLL PROG 16SSOP |
| 標準包裝： | 1,500 |
| 類型： | 時鐘/頻率合成器 |
| PLL： | 是 |
| 輸入： | 晶體 |
| 輸出： | CMOS，PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:1 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 300MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁
FS7140, FS7145
http://onsemi.com
9
If either a STOP or a repeated START condition occurs
during a register write, the data that has been transferred is
ignored.
Random Register Read Procedure
Random read operations allow the master to directly read
from any register. To perform a read procedure, the R/W bit
that is transmitted after the sevenbit address is a logiclow,
as in the register write procedure. This indicates to the
addressed slave device that a register address will follow
after the slave device acknowledges its device address. The
register address is then written into the slave’s address
pointer.
Following an acknowledge by the slave, the master
generates a repeated START condition. The repeated
START terminates the write procedure, but not until after the
slave’s address pointer is set. The slave address is then
resent, with the R/W bit set this time to a logichigh,
indicating to the slave that data will be read. The slave will
acknowledge the device address, and then transmits the
eightbit word. The master does not acknowledge the
transfer but does generate a STOP condition.
Sequential Register Write Procedure
Sequential write operations allow the master to write to
each register in order. The register pointer is automatically
incremented after each write. This procedure is more
efficient than the random register write if several registers
must be written.
To initiate a write procedure, the R/W bit that is
transmitted after the sevenbit device address is a logiclow.
This indicates to the addressed slave device that a register
address will follow after the slave device acknowledges its
device address. The register address is written into the
slave’s address pointer. Following an acknowledge by the
slave, the master is allowed to write up to eight bytes of data
into the addressed register before the register address pointer
overflows back to the beginning address.
An acknowledge by the device between each byte of data
must occur before the next data byte is sent.
Registers are updated every time the device sends an
acknowledge to the host. The register update does not wait
for the STOP condition to occur. Registers are therefore
updated at different times during a sequential register write.
Sequential Register Read Procedure
Sequential read operations allow the master to read from
each register in order. The register pointer is automatically
incremented by one after each read. This procedure is more
efficient than the random register read if several registers
must be read.
To perform a read procedure, the R/W bit that is
transmitted after the sevenbit address is a logiclow, as in
the register write procedure. This indicates to the addressed
slave device that a register address will follow after the slave
device acknowledges its device address. The register
address is then written into the slave’s address pointer.
Following an acknowledge by the slave, the master
generates a repeated START condition. The repeated
START terminates the write procedure, but not until after the
slave’s address pointer is set. The slave address is then
resent, with the R/W bit set this time to a logichigh,
indicating to the slave that data will be read. The slave will
acknowledge the device address, and then transmits all eight
bytes of data starting with the initial addressed register. The
register address pointer will overflow if the initial register
address is larger than zero. After the last byte of data, the
master does not acknowledge the transfer but does generate
a STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B1Y-MY-F2 | CONVERTER MOD DC/DC 3.3V 33W |
| GTC02R-28-15S | CONN RCPT 35POS BOX MNT W/SCKT |
| VI-JV0-MZ-F1 | CONVERTER MOD DC/DC 5V 25W |
| VI-25H-MW-F1 | CONVERTER MOD DC/DC 52V 100W |
| MS27472E24F2SB | CONN RCPT 100POS WALL MT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FS714X | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Programmable Phase-Locked Loop Clock Generator |
| FS7-4 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flow Switches - Liquid |
| FS7-4D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flow Switches - Liquid |
| FS7-4DF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flow Switches - Liquid |
| FS7-4DS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Flow Switches - Liquid |
發布緊急采購，3分鐘左右您將得到回復。