- 您現在的位置：買賣IC網 > PDF目錄17111 > EVAL-ADUC7024QSZ (Analog Devices Inc)KIT DEV QUICK START ADUC7024 PDF資料下載
參數資料
| 型號： | EVAL-ADUC7024QSZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 53/104頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT DEV QUICK START ADUC7024 |
| 產品培訓模塊： | ARM7 Applications & Tools Intro to ARM7 Core & Microconverters |
| 設計資源： | ADUC7024 Dev System Schematic/Brd Outline 7024 Gerber Files |
| 標準包裝： | 1 |
| 系列： | QuickStart™ 套件 |
| 類型： | MCU |
| 適用于相關產品： | ADuC7024 |
| 所含物品： | 評估板、電源、纜線、軟件和說明文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
ADuC7019/20/21/22/24/25/26/27/28/29
Data Sheet
Rev. F | Page 52 of 104
SECURITY
The 62 kB of Flash/EE memory available to the user can be read
and write protected.
Bit 31 of the FEEPRO/FEEHIDE MMR (see Table 42) protects
the 62 kB from being read through JTAG programming mode.
The other 31 bits of this register protect writing to the flash
memory. Each bit protects four pages, that is, 2 kB. Write
protection is activated for all types of access.
Three Levels of Protection
Protection can be set and removed by writing directly into
FEEHIDE MMR. This protection does not remain after reset.
Protection can be set by writing into the FEEPRO MMR. It
takes effect only after a save protection command (0x0C)
and a reset. The FEEPRO MMR is protected by a key to
avoid direct access. The key is saved once and must be
entered again to modify FEEPRO. A mass erase sets the
key back to 0xFFFF but also erases all the user code.
Flash can be permanently protected by using the FEEPRO
MMR and a particular value of key: 0xDEADDEAD.
Entering the key again to modify the FEEPRO register
is not allowed.
Sequence to Write the Key
1. Write the bit in FEEPRO corresponding to the page to be
protected.
2. Enable key protection by setting Bit 6 of FEEMOD (Bit 5
must equal 0).
3. Write a 32-bit key in FEEADR and FEEDAT.
4. Run the write key command 0x0C in FEECON; wait for
the read to be successful by monitoring FEESTA.
5. Reset the part.
To remove or modify the protection, the same sequence is used
with a modified value of FEEPRO. If the key chosen is the value
0xDEAD, the memory protection cannot be removed. Only a mass
erase unprotects the part, but it also erases all user code.
The sequence to write the key is illustrated in the following
example (this protects writing Page 4 to Page 7 of the Flash):
FEEPRO=0xFFFFFFFD;
//Protect pages 4 to 7
FEEMOD=0x48;
//Write key enable
FEEADR=0x1234;
//16 bit key value
FEEDAT=0x5678;
//16 bit key value
FEECON= 0x0C;
// Write key command
The same sequence should be followed to protect the part
permanently with FEEADR = 0xDEAD and FEEDAT = 0xDEAD.
FLASH/EE CONTROL INTERFACE
Serial and JTAG programming use the Flash/EE control interface,
which includes the eight MMRs outlined in this section.
Table 31. FEESTA Register
Name
Address
Default Value
Access
FEESTA
0xFFFFF800
0x20
R
FEESTA is a read-only register that reflects the status of the
flash control interface as described in Table 32.
Table 32. FEESTA MMR Bit Designations
Bit
Description
15:6
Reserved.
5
Reserved.
4
Reserved.
3
Flash interrupt status bit. Set automatically when an
interrupt occurs, that is, when a command is complete
and the Flash/EE interrupt enable bit in the FEEMOD
register is set. Cleared when reading the FEESTA register.
2
Flash/EE controller busy. Set automatically when the
controller is busy. Cleared automatically when the
controller is not busy.
1
Command fail. Set automatically when a command
completes unsuccessfully. Cleared automatically when
reading the FEESTA register.
0
Command pass. Set by the MicroConverter when a
command completes successfully. Cleared automatic-
ally when reading the FEESTA register.
Table 33. FEEMOD Register
Name
Address
Default Value
Access
FEEMOD
0xFFFFF804
0x0000
R/W
FEEMOD sets the operating mode of the flash control interface.
Table 34 shows FEEMOD MMR bit designations.
Table 34. FEEMOD MMR Bit Designations
Bit
Description
15:9
Reserved.
8
Reserved. This bit should always be set to 0.
7:5
Reserved. These bits should always be set to 0 except
when writing keys. See the Sequence to Write the Key
section.
4
Flash/EE interrupt enable. Set by user to enable the
Flash/EE interrupt. The interrupt occurs when a
command is complete. Cleared by user to disable
the Flash/EE interrupt.
3
Erase/write command protection. Set by user to
enable the erase and write commands. Cleared to
protect the Flash against the erase/write command.
2:0
Reserved. These bits should always be set to 0.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADUC845QSZ | KIT DEV FOR ADUC845 QUICK START |
| HCM15DRXS | CONN EDGECARD 30POS DIP .156 SLD |
| EVAL-ADUC832QSZ | KIT DEV FOR ADUC832 QUICK START |
| HBM15DRXS | CONN EDGECARD 30POS DIP .156 SLD |
| PCX1H270MCL1GS | CAP ALUM 27UF 50V 20% SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADUC7026QS | 制造商:Analog Devices 功能描述:MICROCONTROLLER, PRECISION ANALOG,MULTI-CHANNEL 12-BIT ADC - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT |
| EVAL-ADUC7026QSP | 制造商:Analog Devices 功能描述:Evaluation Board For Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT |
| EVAL-ADUC7026QSPZ | 功能描述:KIT DEV ADUC7026/7027 QUICK PLUS RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 產品培訓模塊:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色產品:Blackfin? BF50x Series Processors 標準包裝:1 系列:Blackfin® 類型:DSP 適用于相關產品:ADSP-BF548 所含物品:板，軟件，4x4 鍵盤，光學撥輪，QVGA 觸摸屏 LCD 和 40G 硬盤 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相關產品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADUC7026QS-U1 | 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk |
| EVAL-ADUC7026QSZ | 功能描述:KIT DEV FOR ADUC7026/7027 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。