- 您現在的位置：買賣IC網 > PDF目錄362803 > EVAL-ADF4360-0EB1 (Analog Devices, Inc.) Integrated Synthesizer and VCO PDF資料下載
參數資料
| 型號： | EVAL-ADF4360-0EB1 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | XO, clock |
| 英文描述： | Integrated Synthesizer and VCO |
| 中文描述： | 綜合合成器和VCO |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 432K |
| 代理商： | EVAL-ADF4360-0EB1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
ADF4360-0
MUXOUT AND LOCK DETECT
The output multiplexer on the ADF4360 family allows the user
to access various internal points on the chip. The state of
MUXOUT is controlled by M3, M2, and M1 in the function
latch. The full truth table is shown in Table 7. Figure 13 shows
the MUXOUT section in block diagram form.
Lock Detect
MUXOUT can be programmed for two types of lock detect:
digital and analog. Digital lock detect is active high. When LDP
in the R counter latch is set to 0, digital lock detect is set high
when the phase error on three consecutive phase detector cycles
is less than 15 ns.
Rev. 0 | Page 10 of 20
With LDP set to 1, five consecutive cycles of less than 15 ns
phase error are required to set the lock detect. It stays set high
until a phase error of greater than 25 ns is detected on any sub-
sequent PD cycle.
The N-channel open-drain analog lock detect should be oper-
ated with an external pull-up resistor of 10 k nominal. When a
lock has been detected, this output is high with narrow low-
going pulses.
R COUNTER OUTPUT
N COUNTER OUTPUT
DIGITAL LOCK DETECT
DGND
CONTROL
MUX
MUXOUT
DV
DD
ANALOG LOCK DETECT
SDOUT
0
Figure 13. MUXOUT Circuit
INPUT SHIFT REGISTER
The ADF4360 family’s digital section includes a 24-bit input
shift register, a 14-bit R counter, and an 18-bit N counter,
comprised of a 5-bit A counter and a 13-bit B counter. Data is
clocked into the 24-bit shift register on each rising edge of CLK.
The data is clocked in MSB first. Data is transferred from the
shift register to one of four latches on the rising edge of LE. The
destination latch is determined by the state of the two control
bits (C2, C1) in the shift register. These are the two LSBs, DB1
and DB0, as shown in Figure 2.
The truth table for these bits is shown in Table 5. Table 6 shows
a summary of how the latches are programmed. Note that the
test modes latch is used for factory testing and should not be
programmed by the user.
Table 5. C2 and C1 Truth Table
Control Bits
C2
C1
0
0
0
1
1
0
1
1
VCO
The VCO core in the ADF4360 family uses eight overlapping
bands, as shown in Figure 14, to allow a wide frequency range to
be covered without a large VCO sensitivity (K
V
) and resultant
poor phase noise and spurious performance.
Control Latch
R Counter
N Counter (A and B)
Test Modes Latch
The correct band is chosen automatically by the band select
logic at power-up or whenever the N counter latch is updated. It
is important that the correct write sequence be followed at
power-up. This sequence is
1.
2.
3.
R counter latch
Control latch
N counter latch
During band select, which takes five PFD cycles, the VCO V
TUNE
is disconnected from the output of the loop filter and connected
to an internal reference voltage.
0
0.5
0.7
0.9
1.1
1.3
1.5
1.9
2.1
2.3
1.7
2.5
V
FREQUENCY (MHz)
2200
2400
2600
2800
3000
Figure 14. Frequency vs. V
TUNE
, ADF4360-0
The R counter output is used as the clock for the band select logic
and should not exceed 1 MHz. A programmable divider is provided
at the R counter input to allow division by 1, 2, 4, or 8 and is con-
trolled by Bits BSC1 and BSC2 in the R counter latch. Where the
required PFD frequency exceeds 1 MHz, the divide ratio should be
set to allow enough time for correct band selection.
After band select, normal PLL action resumes. The nominal
value of K
V
is 56 MHz/V or 28 MHz/V, if divide-by-2 operation
has been selected (by programming DIV2 (DB22) high in the N
counter latch). The ADF4360 family contains linearization cir-
cuitry to minimize any variation of the product of I
CP
and K
V
.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADF4360-1EB1 | Integrated Synthesizer and VCO |
| EVAL-ADF4360-3EB1 | Integrated Synthesizer and VCO |
| EVAL-ADF4360-5EB1 | Integrated Synthesizer and VCO |
| EVAL-ADF4360-6EB1 | Integrated Synthesizer and VCO |
| EVAL-ADF4360-8EB1 | Integrated Synthesizer and VCO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADF4360-1EB1 | 制造商:Analog Devices 功能描述:Evaluation Board For ADF4360-1 |
| EVAL-ADF4360-1EBZ1 | 功能描述:BOARD EVALUATION FOR ADF4360-1 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| EVAL-ADF4360-2EB1 | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADF4360-2 |
| EVAL-ADF4360-2EBZ1 | 功能描述:BOARD EVALUATION FOR ADF4360-2 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVAL-ADF4360-3EB1 | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR ADF4360-3 |
發布緊急采購，3分鐘左右您將得到回復。