- 您現在的位置：買賣IC網 > PDF目錄362802 > EVAL-AD7713EB (Analog Devices, Inc.) CAP CERAMIC 1.0UF 10V 10% X7R 0805 SMD PDF資料下載
參數資料
| 型號： | EVAL-AD7713EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | CAP CERAMIC 1.0UF 10V 10% X7R 0805 SMD |
| 中文描述： | LC2MOS回路供電ADC的信號調理 |
| 文件頁數： | 21/28頁 |
| 文件大?。?/td> | 516K |
| 代理商： | EVAL-AD7713EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2
–21–
REV. C
AD7713
SDATA (O)
SCLK (I)
3-STATE
RFS (I)
A0 (I)
t
22
MSB
LSB
DRDY (O)
t
21
t
20
t
23
t
26
t
29
t
28
t
27
t
25
t
24
Figure 12a. External Clocking Mode, Output Data Read Operation
3-STATE
MSB
BIT N
BIT N+1
SDATA (O)
SCLK (I)
RFS (I)
A0 (I)
DRDY (O)
t
22
t
20
t
31
t
26
t
24
t
25
t
27
t
30
t
24
t
25
Figure 12b. External Clocking Mode, Output Data Read Operation (
RFS
Returns High During Read Operation)
RFS
, the next bit (BIT N + 1) may appear on the databus be-
fore
RFS
goes high. When
RFS
returns low again, it activates
the SDATA output. When the entire word is transmitted, the
DRDY
line will go high, turning off the SDATA output as per
Figure 12a.
Write Operation
Data can be written to either the control register or calibration
registers. In either case, the write operation is not affected by
the
DRDY
line, and the write operation does not have any effect
on the status of
DRDY
. A write operation to the control regis-
ter or the calibration register must always write 24 bits to the re-
spective register.
Figure 13a shows a write operation to the AD7713 with
TFS
remaining low for the duration of the write operation. A0 deter-
mines whether a write operation transfers data to the control
register or to the calibration registers. This A0 signal must
remain valid for the duration of the serial write operation. As
before, the serial clock line should be low between read and
write operations. The serial data to be loaded to the AD7713
must be valid on the high level of the externally applied SCLK
signal. Data is clocked into the AD7713 on the high level of this
SCLK signal with the MSB transferred first. On the last active
high time of SCLK, the LSB is loaded to the AD7713.
Figure 13b shows a timing diagram for a write operation to the
AD7713 with
TFS
returning high during the write operation
and returning low again to write the rest of the data word. Tim-
ing parameters and functions are very similar to that outlined for
Figure 13a, but Figure 13b has a number of additional times to
show timing relationships when
TFS
returns high in the middle
of transferring a word.
SCLK (I)
SDATA (I)
TFS (I)
A0 (I)
MSB
LSB
t
32
t
33
t
34
t
26
t
27
t
36
t
35
Figure 13a. External Clocking Mode, Control/Calibration Register Write Operation
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7714-3EB | 3 V/5 V, CMOS, 500 uA Signal Conditioning ADC |
| EVAL-AD7714-5EB | 3 V/5 V, CMOS, 500 uA Signal Conditioning ADC |
| EVAL-AD7715-3EB | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| EVAL-AD7715-5EB | 3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| EVAL-AD7716EB | Evaluation Board For 22-Bit Data Acquisition System |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7714-3EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Bulk |
| EVAL-AD7714-3EBZ | 功能描述:BOARD EVAL FOR AD7714 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7714-5EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD - Bulk |
| EVAL-AD7715-3EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| EVAL-AD7715-3EBZ | 功能描述:BOARD EVALUATION FOR AD7715 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。