參數資料
型號： EVAL-AD5663REB
廠商： Analog Devices, Inc.
英文描述： Dual 12-/14-/16-Bit nanoDAC with 5 ppm/C On-Chip Reference
中文描述： 5分之/ C對芯片參考雙12-/14-/16-Bit nanoDAC系列
文件頁數： 20/28頁
文件大小： 1176K
代理商： EVAL-AD5663REB
AD5623R/AD5643R/AD5663R
THEORY OF OPERATION
DIGITAL-TO-ANALOG SECTION
The AD5623R/AD5643R/AD5663R DAC is fabricated on
a CMOS process. The architecture consists of a string DAC
followed by an output buffer amplifier. Figure 49 shows a block
diagram of the DAC architecture.
Rev. A | Page 20 of 28
DAC
REGISTER
RESISTOR
STRING
REF (–)
REF (+)
V
DD
GND
V
OUT
OUTPUT
AMPLIFIER
(GAIN = +2)
0
Figure 49. DAC Architecture
Because the input coding to the DAC is straight binary, the ideal
output voltage when using an external reference is given by
×
=
N
REFIN
V
OUT
D
2
V
The ideal output voltage when using the internal reference is
given by
×
×
=
N
REFOUT
OUT
D
2
V
V
2
where:
D
is the decimal equivalent of the binary code that is loaded to
the DAC register:
0 to 4095 for AD5623R (12-bit)
0 to 16,383 for AD5643R (14-bit)
0 to 65,535 for AD5663R (16-bit)
N
is the DAC resolution.
RESISTOR STRING
The resistor string section is shown in Figure 50. It is simply a
string of resistors, each of Value R. The code loaded to the DAC
register determines at which node on the string the voltage is
tapped off to be fed into the output amplifier. The voltage is
tapped off by closing one of the switches connecting the string
to the amplifier. Because it is a string of resistors, it is guaranteed
monotonic.
OUTPUT AMPLIFIER
The output buffer amplifier can generate rail-to-rail voltages on
its output, which gives an output range of 0 V to V
DD
. It can drive
a load of 2 kΩ in parallel with 1000 pF to GND. The source and
sink capabilities of the output amplifier can be seen in Figure 31.
The slew rate is 1.8 V/μs with a 1/4 to 3/4 full-scale settling time
of 10 μs.
R
R
R
R
R
TO OUTPUT
AMPLIFIER
0
Figure 50. Resistor String
INTERNAL REFERENCE
The AD5623R/AD5643R/AD5663R on-chip reference is off at
power-up and is enabled via a write to a control register. See the
Internal Reference Setup section for details.
The AD56x3R-3 has a 1.25 V, 5 ppm/°C reference, giving a full-
scale output of 2.5 V. The AD56x3R-5 has a 2.5 V, 5 ppm/°C
reference, giving a full-scale output of 5 V. The internal refer-
ence associated with each part is available at the V
REFOUT
pin.
A buffer is required if the reference output is used to drive
external loads. When using the internal reference, it is
recommended that a 100 nF capacitor be placed between
reference output and GND for reference stability.
EXTERNAL REFERENCE
The V
REFIN
pins on the AD56x3R-3 and the AD56x3R-5 allows
the use of an external reference if the application requires it.
The on-chip reference is off at power-up, and this is the default
condition. The AD56x3R-3 and the AD56x3R-5 can be operated
from a single 2.7 V to 5.5 V supply.
SERIAL INTERFACE
The AD5623R/AD5643R/AD5663R have a 3-wire serial interface
(SYNC, SCLK, and DIN) that is compatible with SPI, QSPI, and
MICROWIRE interface standards, as well as with most DSPs.
See Figure 2 for a timing diagram of a typical write sequence.
The write sequence begins by bringing the SYNC line low. Data
from the DIN line is clocked into the 24-bit shift register on the
falling edge of SCLK. The serial clock frequency can be as high
as 50 MHz, making the AD5623R/AD5643R/AD5663R compatible
with high speed DSPs. On the 24th falling clock edge, the last
data bit is clocked in and the programmed function is executed,
for example, a change in DAC register contents and/or a change
in the mode of operation.
相關PDF資料
PDF描述
EVAL-AD5664REB Quad, 12-/14-/16-Bit nanoDACs with 5 ppm/C On-Chip Reference
EVAL-AD5666EB Quad, 16-Bit DAC with 5 ppm/C On-Chip Reference in 14-Lead TSSOP
EVAL-AD5680EB 5 V 18-Bit nanoDAC in a SOT-23
EVAL-AD5821EBZ1 120 mA, Current Sinking, 10-Bit, I2C DAC
EVAL-AD5930EB Programmable Frequency Sweep and Output Burst Waveform Generator
相關代理商/技術參數
參數描述
EVAL-AD5663REBZ 功能描述:BOARD EVAL FOR AD5663 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5664REB 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad, 12-/14-/16-Bit nanoDACs with 5 ppm/C On-Chip Reference
EVAL-AD5664REBZ 功能描述:BOARD EVALUATION FOR AD5664R RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5665REBZ1 功能描述:BOARD EVAL FOR AD5665 TSSOP RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5665REBZ2 功能描述:BOARD EVAL FOR AD5665 LFCSP RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*