- 您現在的位置：買賣IC網 > PDF目錄362743 > EPC1064 (Electronic Theatre Controls, Inc.) Configuration Devices for SRAM-Based LUT Devices PDF資料下載
參數資料
| 型號： | EPC1064 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Configuration Devices for SRAM-Based LUT Devices |
| 中文描述： | 配置SRAM器件基于LUT的器件 |
| 文件頁數： | 8/28頁 |
| 文件大小： | 380K |
| 代理商： | EPC1064 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
8
Altera Corporation
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000 & Mercury Device
Configuration
ACEX 1K, APEX 20K, FLEX 10K, and Mercury devices can be configured
with EPC2, EPC1, or EPC1441 devices. FLEX 6000 devices can be
configured with EPC1 or EPC1441 devices. The EPC2, EPC1, or EPC1441
device stores configuration data in its EPROM array and serially clocks
data out with an internal oscillator. The
OE
,
nCS
, and
DCLK
pins supply
the control signals for the address counter and the output tri-state buffer.
The configuration device sends a serial bitstream of configuration data to
its
DATA
pin, which is routed to the
DATA0
or
DATA
input pin on the
ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury device.
Figure4
shows an ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury device
configured with a single EPC2, EPC1, or EPC1441 device.
Figure 4. ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury Device
Configured with an EPC2, EPC1, or EPC1441 Configuration Device
Table4
describes EPC2, EPC1, and EPC1441 pin functions during
ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, and Mercury device
configuration.
ACEX 1K, APEX 20K, FLEX 10K,
FLEX 6000, or Mercury Device (2)
Configuration
Device
DCLK
DATA
OE
nCS
nINIT_CONF (4)
MSEL0
MSEL1
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
VCC
VCC
GND
GND
(3)
(3)
nCE
(1)
(1)
Notes:
(1)
The pull-up resistor should be connected to the same supply voltage as the
configuration device.
The diagram shows an ACEX 1K, APEX 20K, FLEX 10K or Mercury device, which
has
MSEL0
and
MSEL1
tied to ground. For FLEX 6000 devices,
MSEL
is tied to
ground, and the
DATA0
pin is named
DATA
. EPC2 cannot be used with FLEX 6000
devices. All other connections are the same for ACEX 1K, APEX 20K, FLEX 10K,
FLEX 6000 and Mercury devices.
All pull-up resistors are 1 k
. APEX 20KE pull up resistors are 10 k
. The
OE
,
nCS
,
and
nINIT_CONF
pins on EPC2 devices have internal, user-configurable 1-k
pull-up resistors. If internal pull-up resistors are used, external pull-up resistors
should not be used on these pins.
The
nINIT_CONF
pin is only available on EPC2 devices and has an internal pull up
of 1 k
that is always active. If
nINIT_CONF
is not available or not used,
nCONFIG
must be pulled to V
CC
either directly or through a 1-k
resistor.
(2)
(3)
(4)
相關PDF資料 |
PDF描述 |
|---|---|
| EPC1064V | Configuration Devices for SRAM-Based LUT Devices |
| EPC1213 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1441 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1064 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC1064V | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC1064LC20 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 64Kb 6 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC1064LC-20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EPROM |
| EPC1064LI20 | 功能描述:IC CONFIG DEVICE 65KBIT 20-PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:EPC 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
| EPC1064LI-20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EPROM |
| EPC1064PA1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。