- 您現在的位置：買賣IC網 > PDF目錄362743 > EPC1064 (Electronic Theatre Controls, Inc.) Configuration Devices for SRAM-Based LUT Devices PDF資料下載
參數資料
| 型號： | EPC1064 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Configuration Devices for SRAM-Based LUT Devices |
| 中文描述： | 配置SRAM器件基于LUT的器件 |
| 文件頁數： | 12/28頁 |
| 文件大小： | 380K |
| 代理商： | EPC1064 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
12
Altera Corporation
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
1
A mixture of ACEX 1K, APEX 20K, APEX 20KE, and Mercury
devices can be configured in the same chain. A mixture of
FLEX 10K, FLEX 10KA, FLEX 10KE, and 5.0-V and 3.3-V
FLEX 6000 devices can be configured in the same chain. See
“
Configuration Chain with Multiple Voltage Levels
”
on page 19
.
Figure 5. ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or Mercury Device Configured with Two EPC2 or EPC1
Configuration Devices
Notes:
(1)
(2)
The pull-up resistor should be connected to the same supply voltage as the configuration device.
The diagram shows an ACEX 1K, APEX 20K, FLEX 10K, or Mercury device, which has
MSEL0
and
MSEL1
tied to
ground. For FLEX 6000 devices,
MSEL
is tied to ground, and the
DATA0
pin is named
DATA
. EPC2 cannot be used
with FLEX 6000 devices. All other connections are the same for ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, and
Mercury devices.
All pull-up resistors are 1 k
(APEX 20KE pull-resistors are 10k
). The
OE
and
nCS
pins on EPC2 devices have
internal, user-configurable 1-k
pull-up resistors. If internal pull-up resistors are used, external pull-up resistors
should not be used on these pins.
The
nINIT_CONF
pin is only available on EPC2 devices and has an internal pull up of 1 k
that is always active. If
nINIT_CONF
is not available or not used,
nCONFIG
must be pulled to V
CC
either directly or through a 1-k
resistor.
(3)
(4)
Figure6
shows two ACEX 1K, APEX 20K, FLEX 10K, FLEX 6000, or
Mercury devices configured with two EPC2 or EPC1 devices.
Configuration
Device 1
DCLK
DATA
OE
nCS
nINIT_CONF (4)
MSEL0
MSEL1
DCLK
DATA0
nSTATUS
CONF_DONE
nCONFIG
VCC
VCC
GND
GND
(3)
nCE
DCLK
DATA
nCS
OE
Configuration
Device 2
(3)
(1)
(1)
nCASC
ACEX 1K, APEX 20K, FLEX 10K,
FLEX 6000, or Mercury Device (2)
相關PDF資料 |
PDF描述 |
|---|---|
| EPC1064V | Configuration Devices for SRAM-Based LUT Devices |
| EPC1213 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1441 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1064 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
| EPC1064V | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC1064LC20 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 64Kb 6 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC1064LC-20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EPROM |
| EPC1064LI20 | 功能描述:IC CONFIG DEVICE 65KBIT 20-PLCC RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:EPC 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件 |
| EPC1064LI-20 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Configuration EPROM |
| EPC1064PA1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。