參數資料
型號： EMC2103-2-AP-TR
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 模擬信號調理
中文描述： SPECIALTY ANALOG CIRCUIT, QCC16
封裝： 4 X 4 MM, ROHS COMPLIANT, QFN-16
文件頁數： 28/89頁
文件大小： 1243K
代理商： EMC2103-2-AP-TR
RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
Revision 0.90 (08-19-08)
34
SMSC EMC2103
DATASHEET
5.8
Ramp Rate Control
The PWM output drive can be configured with automatic ramp rate control. If the RPM based Fan
Speed Control Algorithm is used, then this ramp rate control is automatically used based on the fan
control derivative option settings. See Section 6.23, "Fan Configuration 2 Register". The user programs
a maximum step size for the PWM setting and an update time. The update time varies from 100ms to
1.6s while the PWM maximum step can vary from 1 PWM count to 31 PWM counts.
When a new PWM is entered, the delta from the next PWM and the previous PWM is determined. If
this delta is greater than the Max Step settings, then the PWM is incrementally adjusted every 100ms
to 1.6s as determined by the Update Time until the target PWM setting is reached. See Figure 5.6.
5.9
Watchdog Timer
The EMC2103 contains an internal Watchdog Timer. Once the device has powered up the watchdog
timer monitors the bus traffic for signs of activity. The Watchdog Timer starts when the internal supply
has reached its operating point. The Watchdog Timer only starts immediately after power-up and once
it has been triggered or deactivated will not restart.
If four (4) seconds elapse without the system host programming the device, then the watchdog will be
triggered and the following will occur:
1. The WATCH status bit will be set.
2. The fan driver will be set to full scale drive. It will remain at full scale drive until one of the three
conditions listed below are met.
If the Watchdog Timer is triggered, the following three operations will disable the timer and return the
device to normal operation. Alternately, if the Watchdog Timer has not yet been triggered performing
any one of the following will disable it.
1. Writing the Fan Setting Register will disable the Watchdog Timer.
2. Enabling the RPM based Fan Speed Control Algorithm by setting the EN_ALGO bit will disable the
Watchdog Timer. The fan driver will be set based on the RPM based Fan Speed Control Algorithm.
Figure 5.6 Ramp Rate Control
Previous
Setting
Next Desired
Setting
Max
Step
Max
Step
Update
Time
Update
Time
Setting Changed
相關PDF資料
PDF描述
EMCL12C2J-35.000MTR CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT
EMCL12C2J-40.000M CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT
EMCL12D2H-30.000MTR CRYSTAL OSCILLATOR, CLOCK, 30 MHz, LVPECL OUTPUT
EMCL12D2H-40.000MTR CRYSTAL OSCILLATOR, CLOCK, 40 MHz, LVPECL OUTPUT
EMCL12D2J-35.000MTR CRYSTAL OSCILLATOR, CLOCK, 35 MHz, LVPECL OUTPUT
相關代理商/技術參數
參數描述
EMC2103-3-KP 制造商:SMSC 制造商全稱:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown
EMC2103-4 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Analog and Interface Product Selector Guide
EMC2103-4-AP 制造商:SMSC 制造商全稱:SMSC 功能描述:RPM-Based Fan Controller with HW Thermal Shutdown
EMC2103-4-AP-TR 功能描述:板上安裝溫度傳感器 RPM-BASED FAN CTRL HW THRML SHUTDWN RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
EMC2104 制造商:SMSC 制造商全稱:SMSC 功能描述:Dual RPM-Based PWM Fan Controller with Hardware Thermal Shutdown
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*