- 您現在的位置：買賣IC網 > PDF目錄362657 > ELANSC400-33AC (ADVANCED MICRO DEVICES INC) Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers PDF資料下載
參數資料
| 型號： | ELANSC400-33AC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| 中文描述： | 32-BIT, FLASH, 33 MHz, MICROCONTROLLER, PBGA292 |
| 封裝： | PLASTIC, BGA-292 |
| 文件頁數： | 79/132頁 |
| 文件大?。?/td> | 2400K |
| 代理商： | ELANSC400-33AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁當前第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁
élanSC400 and élanSC410 Microcontrollers Data Sheet
79
32-kHz Crystal Oscillator
The 32-kHz oscillator circuit is shown in Figure 6; the
only external component required for operation is a
32.768-kHz crystal. The inverting amplifier (AMP) is in-
tegrated on-chip together with the feedback resistor
and the load capacitors. As shown in Figure 7, the on-
chip oscillator circuit can be bypassed by removing the
external crystal, grounding the 32KXTAL1 pin, and
driving the 32KXTAL2 pin with an external 32-kHz
clock. (The 32KXTAL2 pin should not exceed 2.0 V.)
When 32KXTAL1 is grounded, the amplifier no longer
affects the circuit.
Figure 6.
32-kHz Crystal Circuit
Figure 7.
32-kHz Oscillator Circuit
Loop Filters
Each of the PLLs in the élanSC400 and élanSC410 mi-
crocontrollers requires an external loop filter. For a
cleaner circuit, the designer should consider the following:
I
Place the loop filter components as close as
possible to the loop filter signals (LF_INT, LF_LS,
LF_HS, and LF_VID (élanSC400 microcontroller
only)), which are located in one corner of the
microcontroller.
I
Route the loop filter signals first and by hand.
I
Keep all clocks and noisy signals away from the
loop filter area (even on the inner layers).
For an even cleaner circuit, the designer could option-
ally place an analog V
CC
power plane directly under the
loop filter circuit.
The value of the loop filter parameters can also affect
the performance of the filter. For example, the values of
C1 and R affect lock time and jitter (increasing RC in-
creases lock time and decreases jitter). The value of
C2 can help clean up high-frequency noise. Note that
using too large of values for the components can cause
the PLL to become unstable. The loop filter component
value specifications are shown in Table 28 on page 84.
Intermediate and Low-Speed PLLs
Figure 8 on page 80 shows the block diagram for both
the Intermediate and Low-Speed PLLs. Each consists
of a phase detector, a charge pump, a voltage con-
trolled oscillator (VCO), an external loop filter, and a
feedback divider. This is a generic implementation of
the charge-pump PLL architecture; all four PLLs use
the same architecture. The Intermediate and Low-
Speed PLLs differ only in component values and fre-
quency of operation.
The phase detector compares the phase and fre-
quency of the two clock signals, reference frequency
(Fr) and feedback frequency (Ff). The Up signal is a
logic 1 if Fr leads Ff, while the Down signal is a logic 1
if Ff leads Fr. The Up and Down signals control the
charge pump. The charge pump either charges or dis-
charges the loop filter capacitors to change the VCO
input voltage level. Because the VCO output frequency
tracks the VCO input voltage, the VCO output fre-
quency is adjusted whenever Fr and Ff differ in phase
or frequency.
The feedback divide ratio determines the frequency
multiplication factor.
Frequency multiplication is 1/(Feedback Divider).
For the Intermediate PLL, the feedback divider is 1/45;
therefore, the frequency multiplication is 45. With an
input frequency of 32.768 kHz, the output frequency is
1.47456 MHz.
The input clock for the Low-Speed PLL, Fr, originates
at the Intermediate PLL output. Fr is multiplied by 25 to
generate the 36.864-MHz clock output.
AMP
32KXTAL2
32.768-kHz Crystal
32KXTAL1
Internal
External
32 kHz
32KXTAL1
Oscillator
32KXTAL2
2 V
max
Pin #Y4
相關PDF資料 |
PDF描述 |
|---|---|
| ELANSC400-33AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC400-66AC | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC400-66AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-100AC | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-100AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC400-33AC-REVA3 | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC ROMLess 3.3V 292-Pin BGA |
| ELANSC400-33AI | 制造商:Advanced Micro Devices 功能描述:MCU 32-bit Elan RISC ROMLess 3.3V 292-Pin BGA |
| ELANSC400-33AIAD | 制造商:Advanced Micro Devices 功能描述: |
| ELANSC400-66AC | 制造商:Advanced Micro Devices 功能描述: |
| ELANSC400-66AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。