- 您現在的位置：買賣IC網 > PDF目錄362657 > ELANSC300-33VC (ADVANCED MICRO DEVICES INC) Highly Integrated, Low-Power, 32-Bit Microcontroller PDF資料下載
參數資料
| 型號： | ELANSC300-33VC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| 中文描述： | 32-BIT, 33 MHz, MICROCONTROLLER, PQFP208 |
| 封裝： | TQFP-208 |
| 文件頁數： | 38/139頁 |
| 文件大小： | 1388K |
| 代理商： | ELANSC300-33VC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁
38
élanSC300 Microcontroller Data Sheet
P R E L I M I N A R Y
SLCTIN [PCMCOE]
Printer Selected (Output; Active Low)
Asserting SLCTIN selects the line printer. This pin can
be programmed to become the PCMCIA output enable
signal (PCMCOE). For more information, see
“Parallel
Port” on page 61.
STRB
Strobe (Output; Active Low)
Asserting STRB signals the line printer to latch data
currently on the parallel port.
SERIAL PORT INTERFACE
CTS
Clear To Send (Input; Active Low)
This signal indicates that the external serial device is
ready to accept data.
DCD
Data Carrier Detect (Input; Active Low)
This signal indicates to the internal serial port controller
that the attached serial device has detected a data car-
rier.
DSR
Data Set Ready (Input; Active Low)
This signal is used to indicate that the external serial
device is ready to establish a communication link with
the internal serial port controller.
DTR/CFG1
Data Terminal Ready (Output; Active Low)
This signal indicates to the external serial device that
the internal serial port controller is ready to communi-
cate.
The state of this signal is used to determine the pin
configuration at power-up. For more information, see
“Alternate Pin Functions” on page 68.
RIN
Ring Indicate (Input; Active Low)
This signal is used as a modem control function. A
change in state on this signal by the external serial de-
vice causes a modem status interrupt. This signal can
be used to cause the élanSC300 microcontroller to re-
sume from a suspended state.
RTS/CFG0
Request To Send (Output; Active Low)
This signal indicates to the external serial device that
the internal serial port controller is ready to send data.
The state of this signal is used to determine the pin
configuration at power-up. For more information, see
“Alternate Pin Functions” on page 68.
SIN
Serial Data In (Input; Active High)
This signal is used to receive the serial data from the
external serial device into the internal serial port
controller.
SOUT
Serial Data Out (Output; Active High)
This signal is used to transmit the serial data from the
internal serial port controller to the external serial
device.
PCMCIA INTERFACE
BVD1_A (STSCHG_A), BVD1_B (STSCHG_B)
Battery Voltage Detect (Inputs)
These signals are generated by the memory card as an
indication of the condition of its battery for a memory
card interface. For an I/O card interface, these inputs
are the card’s Status Change Interrupt (active Low).
BVD2_A (SPKR_A), BVD2_B (SPKR_B)
Battery Voltage Detect (Inputs)
These signals are generated by the memory card as an
indication of the condition of its battery for a memory
card interface. For an I/O card interface, these pins be-
come the speaker inputs from the cards.
CA24
Card Address Bit 24 (Output)
This card address bit is controlled by accessing the
élanSC300 microcontroller configuration registers and
should be connected to the card interface signal A24.
This address signal is common to slot A and slot B in-
terfaces.
CA25
Card Address Bit 25 (Output)
This card address bit is controlled by accessing the
élanSC300 microcontroller configuration registers, and
should be connected to the card interface signal A25.
This address signal is common to slot A and slot B in-
terfaces.
CD_A, CD_B
Card Detect (Inputs; Active Low)
The card detect signals indicate that the card is prop-
erly inserted into a socket. These signals should be
driven from an “ANDing” of the CD1 and CD2 pins of a
single socket. Therefore, two external AND gates are
required, one for each slot.
相關PDF資料 |
PDF描述 |
|---|---|
| ELANSC300 | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| ELANSC300-25KC | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| ELANSC300-25KI | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| ELANSC300-25VC | Highly Integrated, Low-Power, 32-Bit Microcontroller |
| ELANSC300-25VI | Highly Integrated, Low-Power, 32-Bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC300-33VI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Highly Integrated, Low-Power, 32-Bit Microcontroller |
| ELANSC300WW WAF | 制造商:Advanced Micro Devices 功能描述: |
| ELANSC310 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Elan SC310 - Elan SC310 Single-Chip. 32-Bit. PC/AT Microcontroller |
| ELANSC310-25 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, 32-Bit, PC/AT Microcontroller |
| ELANSC310-25KC | 制造商:ADVANCED MICRO DEVICES,INC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。