參數資料
型號: DSPB56371AF150
廠商: Freescale Semiconductor
文件頁數: 19/68頁
文件大?。?/td> 0K
描述: IC DSP 24BIT 150MHZ 80-LQFP
標準包裝: 90
系列: DSP56K/Symphony
類型: 音頻處理器
接口: 主機接口,I²C,SAI,SPI
時鐘速率: 150MHz
非易失內存: ROM(384 kB)
芯片上RAM: 264kB
電壓 - 輸入/輸出: 3.30V
電壓 - 核心: 1.25V
工作溫度: -40°C ~ 115°C
安裝類型: 表面貼裝
封裝/外殼: 80-LQFP
供應商設備封裝: 80-LQFP(14x14)
包裝: 托盤
DSP56371 Data Sheet, Rev. 4.1
Signal/Connection Descriptions
Freescale Semiconductor
26
SCKR_1
Input or output
GPIO
disconnected
Receiver Serial Clock_1—SCKR_1 provides the receiver serial
bit clock for the ESAI_1. The SCKR_1 operates as a clock input
or output used by all the enabled receivers in the asynchronous
mode (SYN=0), or as serial flag 0 pin in the synchronous mode
(SYN=1).
When this pin is configured as serial flag pin, its direction is
determined by the RCKD bit in the RCCR_1 register. When
configured as the output flag OF0, this pin will reflect the value of
the OF0 bit in the SAICR_1 register, and the data in the OF0 bit
will show up at the pin synchronized to the frame sync in normal
mode or the slot in network mode. When configured as the input
flag IF0, the data value at the pin will be stored in the IF0 bit in the
SAISR_1 register, synchronized by the frame sync in normal
mode or the slot in network mode.
PE0
Input, output, or
disconnected
Port E0—When the ESAI_1 is configured as GPIO, this signal is
individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SCKT_1
Input or output
GPIO
disconnected
Transmitter Serial Clock_1—This signal provides the serial bit
rate clock for the ESAI_1. SCKT_1 is a clock input or output used
by all enabled transmitters and receivers in synchronous mode,
or by all enabled transmitters in asynchronous mode.
PE3
Input, output, or
disconnected
Port E3—When the ESAI_1 is configured as GPIO, this signal is
individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
SDO5_1
Output
GPIO
disconnected
Serial Data Output 5_1—When programmed as a transmitter,
SDO5_1 is used to transmit data from the TX5 serial transmit shift
register.
SDI0_1
Input
Serial Data Input 0_1—When programmed as a receiver,
SDI0_1 is used to receive serial data into the RX0 serial receive
shift register.
PE6
Input, output, or
disconnected
Port E6—When the ESAI_1 is configured as GPIO, this signal is
individually programmable as input, output, or internally
disconnected.
The default state after reset is GPIO disconnected.
Internal Pull down resistor.
This input is 5 V tolerant.
Table 9. Enhanced Serial Audio Interface_1 Signals
Signal Name
Signal Type
State during
Reset
Signal Description
相關PDF資料
PDF描述
RMM36DRKF-S13 CONN EDGECARD 72POS .156 EXTEND
DSPB56374AFC IC DSP 24BIT 150MHZ 80-LQFP
VI-B6R-CY-F3 CONVERTER MOD DC/DC 7.5V 50W
DCM37S500M CONN DSUB RCPT 37POS T/H RA GOLD
ABB65DHLN CONN EDGECARD 130PS .050 DIP SLD
相關代理商/技術參數
參數描述
DSPB56371AF180 功能描述:數字信號處理器和控制器 - DSP, DSC BLANK ROM VERSION 56371 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPB56371AF180 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor (DSP) IC
DSPB56374AE 功能描述:數字信號處理器和控制器 - DSP, DSC PB-FREE 52 LQFP RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPB56374AEB 制造商:Freescale Semiconductor 功能描述:52 LQFP PB-FREE W/ BI - Bulk
DSPB56374AEC 功能描述:數字信號處理器和控制器 - DSP, DSC 52 LQFP AUTOMOTIVE RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT