- 您現在的位置：買賣IC網 > PDF目錄9362 > DS3234S#T&R (Maxim Integrated Products)IC RTC W/TCXO 20-SOIC PDF資料下載
參數資料
| 型號： | DS3234S#T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC W/TCXO 20-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，閏年，NVSRAM，方波輸出，TCXO/晶體 |
| 存儲容量： | 256B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | SPI |
| 電源電壓： | 2 V ~ 5.5 V |
| 電壓 - 電源，電池： | 2 V ~ 3.8 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC W |
| 包裝： | 帶卷 (TR) |
DS3234
Extremely Accurate SPI Bus RTC with
Integrated Crystal and SRAM
14
____________________________________________________________________
Special-Purpose Registers
The DS3234 has two additional registers (control and
control/status) that control the real-time clock, alarms,
and square-wave output.
Control Register (0Eh/8Eh)
Bit 7: Enable Oscillator (EOSC). When set to logic 0,
the oscillator is started. When set to logic 1, the oscilla-
tor is stopped when the DS3234 switches to battery
power. This bit is clear (logic 0) when power is first
applied. When the DS3234 is powered by VCC, the
oscillator is always on regardless of the status of the
EOSC bit. When EOSC is disabled, all register data is
static.
Bit 6: Battery-Backed Square-Wave Enable
(BBSQW). When set to logic 1 with INTCN = 0 and VCC
< VPF, this bit enables the square wave. When BBSQW
is logic 0, the INT/SQW pin goes high impedance when
VCC < VPF. This bit is disabled (logic 0) when power is
first applied.
Bit 5: Convert Temperature (CONV). Setting this bit to
1 forces the temperature sensor to convert the temper-
ature into digital code and execute the TCXO algorithm
to update the capacitance array to the oscillator. This
can only happen when a conversion is not already in
progress. The user should check the status bit BSY
before forcing the controller to start a new TCXO exe-
cution. A user-initiated temperature conversion does
not affect the internal 64-second (default interval)
update cycle. This bit is disabled (logic 0) when power
is first applied.
A user-initiated temperature conversion does not affect
the BSY bit for approximately 2ms. The CONV bit
remains at a 1 from the time it is written until the conver-
sion is finished, at which time both CONV and BSY go
to 0. The CONV bit should be used when monitoring
the status of a user-initiated conversion.
Bits 4 and 3: Rate Select (RS2 and RS1). These bits
control the frequency of the square-wave output when
the square wave has been enabled. The following table
shows the square-wave frequencies that can be select-
ed with the RS bits. These bits are both set to logic 1
(8.192kHz) when power is first applied.
Bit 2: Interrupt Control (INTCN). This bit controls the
INT/SQW signal. When the INTCN bit is set to logic 0, a
square wave is output on the INT/SQW pin. When the
INTCN bit is set to logic 1, a match between the time-
keeping registers and either of the alarm registers acti-
vates the INT/SQW (if the alarm is also enabled). The
corresponding alarm flag is always set regardless of
the state of the INTCN bit. The INTCN bit is set to logic
1 when power is first applied.
Bit 1: Alarm 2 Interrupt Enable (A2IE). When set to
logic 1, this bit permits the alarm 2 flag (A2F) bit in the
status register to assert INT/SQW (when INTCN = 1).
When the A2IE bit is set to logic 0 or INTCN is set to
logic 0, the A2F bit does not initiate an interrupt signal.
The A2IE bit is disabled (logic 0) when power is first
applied.
Bit 0: Alarm 1 Interrupt Enable (A1IE). When set to
logic 1, this bit permits the alarm 1 flag (A1F) bit in the
status register to assert INT/SQW (when INTCN = 1).
When the A1IE bit is set to logic 0 or INTCN is set to
logic 0, the A1F bit does not initiate the INT/SQW sig-
nal. The A1IE bit is disabled (logic 0) when power is
first applied.
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
NAME:
EOSC
BBSQW
CONV
RS2
RS1
INTCN
A2IE
A1IE
POR*:
000
111
0
RS2
RS1
SQUARE-WAVE OUTPUT
FREQUENCY
0
1Hz
0
1
1.024kHz
1
0
4.096kHz
1
8.192kHz
SQUARE-WAVE OUTPUT FREQUENCY
Control Register (0Eh/8Eh)
*
POR is defined as the first application of power to the device, either VBAT or VCC.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3232S#T&R | IC RTC W/TCXO 20-SOIC |
| VE-BNV-IU-S | CONVERTER MOD DC/DC 5.8V 200W |
| DS3231S#T&R | IC RTC W/TCXO 16-SOIC |
| MAX5389MAUD+ | IC POT DGTL 256-TAP 14TSSOP |
| VE-B63-MW-B1 | CONVERTER MOD DC/DC 24V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS323PIN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| DS-323PIN | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:Flatpack Three-Way Power Divider 25 - 1000 MHz |
| DS-323-PIN | 功能描述:信號調節 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| DS323X | 功能描述:KIT X-WIDE DESIGN STRIP VERT RoHS:是 類別:盒，外殼，支架 >> 插線臺，插座面板 - 配件 系列:X-Wide® 標準包裝:50 系列:- 附件類型:模擬插頭，雙 樣式:耳機，0.173" 直徑 包括:- |
| DS324 | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:32 Megabit (4 M x 8-Bit/2 M x 16-Bit) CMOS 1.8 Volt-only, Simultaneous Operation Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。