- 您現(xiàn)在的位置：買賣IC網 > PDF目錄376968 > DS2406T Dual Addressable Switch Plus 1K-Bit Memory PDF資料下載
參數資料
| 型號： | DS2406T |
| 英文描述： | Dual Addressable Switch Plus 1K-Bit Memory |
| 中文描述： | 雙址開關與1K位存儲器 |
| 文件頁數： | 22/30頁 |
| 文件大?。?/td> | 156K |
| 代理商： | DS2406T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
DS2406
22 of 30
The activity latch (Figure 11) captures an event for interrogation by the bus master at a later time. This
way, the bus master needs not interrogate devices continuously. The activity latch is set to 1 with the first
negative or positive edge detected on the associated PIO channel. It can be cleared with the Channel
Access command if the ALR bit of the Channel Control Byte 1 is set. The activity latch is automatically
cleared when the DS2406 powers up. In order to use the activity latch the output transistor of the selected
channel should be non-conducting. Otherwise signals applied to the PIO pin will be shorted to ground by
the low impedance of the output transistor.
The Channel Select bits CSS3 and CSS4 specify the channel of interest. The sampling of the source
within the selected channel will take place on completion of the Conditional Search command byte. The
Channel selection codes are as follows:
CSS4
0
0
1
1
CSS3
0
1
0
1
Channel Selection
neither channel selected
channel A only
channel B only
channel A OR channel B
If both CSS3 and CSS4 are 1, the logical values of the selected signal source of both channels are ORed
and the result is compared to specified polarity. If, for example, the specified polarity is 0, the signal
source of both channels must be 0 for the device to respond to the Conditional Search. If both CSS3 and
CSS4 are 0, neither channel is selected. Under this condition the device
will always respond
to the
Conditional Search if the polarity bit CSS0 is 0, disregarding the source selection. If neither channel is
selected and CSS0 = 1, the device will only respond to the regular Search ROM command.
The source selection for the Conditional Search is done through the Source Select bits CSS1 and CSS2.
The codes for these bits are as follows:
CSS2
0
0
1
1
CSS1
0
1
0
1
Source Selection
RESERVED
Activity Latch
channel flip flop
PIO Status
The setting CSS1=0, CSS2=0 is reserved for future use. If programmed with this setting the device will
respond to Conditional Search command as follows: if CSS0=0 the device will always respond to a
Conditional Search, if CSS0=1 the device will never respond to a conditional search.
The Conditional Search Polarity is specified by CSS0. If CSS0 is 0, the DS2406 will respond to a
Conditional Search command if the status of the selected source for the specified channel is logic 0. If
CSS0 is set to 1, the source level needs to be logic 1.
For 1-channel versions of the DS2406 the channel B input will always be logic 0. For this reason CSS4
should not be set to 1 to avoid unwanted influence from channel B. The bus master can determine the
availability of channel B from bit 6 of the Channel Info byte.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2406V | Dual Addressable Switch Plus 1K-Bit Memory |
| DS2406X | Dual Addressable Switch Plus 1K-Bit Memory |
| DS2407 | Dual Addressable Switch Plus 1K.Bit Memory |
| DS2407P | Dual Addressable Switch Plus 1K.Bit Memory |
| DS2407T | Dual Addressable Switch Plus 1K.Bit Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2406V | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K-Bit Memory |
| DS2406X | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2407 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K.Bit Memory |
| DS2407FP000 | 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,407,3P250V |
| DS2407MP000 | 制造商:Thomas & Betts 功能描述:200A,PLG,3P4W,MG,407,3P250V |
發(fā)布緊急采購，3分鐘左右您將得到回復。