參數資料
型號： DS2404B
英文描述： EconoRAM Time Chip
中文描述： EconoRAM時鐘芯片
文件頁數： 6/28頁
文件大小： 663K
代理商： DS2404B
DS2404
6 of 28
020998
MEMORY
The memory map in Figure 4 shows a page (32 bytes) called the scratchpad and 17 pages called memory.
Pages 0 through 15 each contain 32 bytes which make up the 4096-bit SRAM. Page 16 has only 30 bytes
which contain the timekeeping registers.
The scratchpad is an additional page of memory that acts as a buffer when writing to memory. Data is
first written to the scratchpad where it can be read back. After the data has been verified, a copy
scratchpad command will transfer the data to memory. This process ensures data integrity when
modifying the memory.
TIMEKEEPING
A 32.768 kHz crystal oscillator is used as the time base for the timekeeping functions. The oscillator can
be turned on or off by an enable bit in the control register. The oscillator must be on for the real time
clock, interval timer, cycle counter and 1 Hz output to function.
The timekeeping functions are double buffered. This feature allows the master to read time or count
without the data changing while it is being read. To accomplish this, a snapshot of the counter data is
transferred to holding registers which the user accesses. This occurs after the eighth bit of the Read
Memory Function command.
Real-Time Clock
The real-time clock is a 5-byte binary counter. It is incremented 256 times per second. The least
significant byte is a count of fractional seconds. The upper four bytes are a count of seconds. The real-
time clock can accumulate 136 years of seconds before rolling over. Time/date is represented by the
number of seconds since a reference point which is determined by the user. For example, 12:00A.M.,
January 1, 1970 could be a reference point.
Interval Timer
The interval timer is a 5-byte binary counter. When enabled, it is incremented 256 times per second. The
least significant byte is a count of fractional seconds. The interval timer can accumulate 136 years of
seconds before rolling over. The interval timer has two modes of operation which are selected by the
MAN
AUTO/
bit in the control register. In the auto mode, the interval timer will begin counting after the
I/O line has been high for a period of time determined by the DSEL bit in the control register. Similarly,
the interval timer will stop counting after the I/O line has been low for a period of time determined by the
DSEL bit. In the manual mode, time accumulation is controlled by the
register.
START
STOP/
bit in the control
NOTE: For auto mode operation, the high level on the I/O pin must be greater than or equal to 70% of
V
CC
or V
BATO
.
Cycle Counter
The cycle counter is a 4-byte binary counter. It increments after the falling edge of the I/O line if the
appropriate I/O line timing has been met. This timing is selected by the DSEL bit in the control register.
(See “Status/ Control” section).
NOTE: For cycle counter operation, the high level on the I/O pin must be greater than or equal to 70% of
V
CC
or V
BATO
.
相關PDF資料
PDF描述
DS2404S EconoRAM Time Chip
DS2405 Addressable Switch
DS2405P Addressable Switch
DS2405T Addressable Switch
DS2405V Addressable Switch
相關代理商/技術參數
參數描述
DS2404B/T&R 制造商:Maxim Integrated Products 功能描述:ECONORAM/TIME, SSOP16-TRL (GENERIC) - Tape and Reel
DS2404B+ 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SSOP - Rail/Tube
DS2404B+T&R 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 512BYTE 16SSOP - Tape and Reel
DS2404FP000 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,404,3P480V
DS2404FP000/DF2029 制造商:Thomas & Betts 功能描述:RS DS2404FP000/DF2029 200A,CON,3P4W
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*