- 您現在的位置：買賣IC網 > PDF目錄97867 > DS21FT44 (MAXIM INTEGRATED PRODUCTS INC) DATACOM, FRAMER, PBGA300 PDF資料下載
參數資料
| 型號： | DS21FT44 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PBGA300 |
| 封裝： | 27 X 27 MM, 1.27 MM PITCH, MCMBGA-300 |
| 文件頁數： | 44/117頁 |
| 文件大小： | 691K |
| 代理商： | DS21FT44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
DS21FT44/DS21FF44
32 of 117
9. PARALLEL PORT
The DS21Q44 is controlled by either a nonmultiplexed (MUX = 0) or a multiplexed (MUX = 1) bus by
an external microcontroller or microprocessor. The DS21Q44 can operate with either Intel or Motorola
bus timing configurations. If the BTS pin is connected low, Intel timing will be selected; if connected
high, Motorola timing will be selected. All Motorola bus signals are listed in parenthesis (). See the
timing diagrams in the A.C. Electrical Characteristics in Section 23 for more details.
10.
CONTROL, ID, AND TEST REGISTERS
The operation of each framer within the DS21Q44 is configured by a set of 10 control registers.
Typically, the control registers are only accessed when the system is first powered up. Once a channel in
the DS21Q44 has been initialized, the control registers will only need to be accessed when there is a
change in the system configuration. There are two Receive Control Register (RCR1 and RCR2), two
Transmit Control Registers (TCR1 and TCR2), and six Common Control Registers (CCR1 to CCR6).
Each of the ten registers are described in this section.
There is a device Identification Register (IDR) at address 0Fh. The MSB of this read-only register is fixed
to a one indicating that the DS21Q44 is present. The T1 pin-for-pin compatible version of the DS21Q44
is the DS21Q42 and it also has an ID register at address 0Fh and the user can read the MSB to determine
which chip is present since in the DS21Q42 the MSB will be set to a 0 and in the DS21Q44 it will be set
to a one. The lower 4 bits of the IDR are used to display the die revision of the chip.
Power-Up Sequence
The DS21Q44 does not automatically clear its register space on power-up. After the supplies are stable,
each of the four framer’s register space should be configured for operation by writing to all of the internal
registers. This includes setting the Test and all unused registers to 00Hex.
This can be accomplished using a two-pass approach on each framer within the DS21Q44.
1) Clear framer’s register space by writing 00H to the addresses 00H through 0BFH.
2) Program required registers to achieve desired operating mode.
NOTE:
When emulating the DS21Q43 feature set (FMS = 1), the full address space (00H through 0BFH) must be
initialized. DS21Q43 emulation require address pin A7 to be used. FMS is connected to ground for the
DS21FF44/DS21FT44.
Finally, after the TSYSCLK and RSYSCLK inputs are stable, the ESR bit should be toggled from a zero
to a one (this step can be skipped if the elastic stores are disabled).
相關PDF資料 |
PDF描述 |
|---|---|
| DS21Q352 | DATACOM, PCM TRANSCEIVER, PBGA256 |
| DS21Q354 | DATACOM, PCM TRANSCEIVER, PBGA256 |
| DS21Q41BT | DATACOM, FRAMER, PQFP128 |
| DS21Q42TN | DATACOM, FRAMER, PQFP128 |
| DS21Q42T | DATACOM, FRAMER, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21FT44+ | 功能描述:網絡控制器與處理器 IC 4X3 E1 Framer E1 Framer E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21FT44N | 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21FT44N+ | 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q348 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q348B | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。