- 您現在的位置：買賣IC網 > PDF目錄11562 > DS21FF42N+ (Maxim Integrated Products)IC FRAMER T1 4X4 16CH 300-BGA PDF資料下載
參數資料
| 型號： | DS21FF42N+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 95/114頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FRAMER T1 4X4 16CH 300-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 控制器類型： | T1 調幀器 |
| 接口： | 并行/串行 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 電流 - 電源： | 300mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 300-BBGA |
| 供應商設備封裝： | 300-PBGA（27x27） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁當前第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁
DS21FT42/DS21FF42
81 of 114
determining which channels are to have Bit 7 stuffing performed. If the TCR2.0 and TCR1.3 bits are set
to one, then all 24 T1 channels will have Bit 7 stuffing performed on them regardless of how the TTR
registers are programmed. In this manner, the TTR registers are only affecting which channels are to
have robbed bit signaling inserted into them. Please see Figure 24-15 for more details.
21.
INTERLEAVED PCM BUS OPERATION
In many architectures, the outputs of individual framers are combined into higher speed serial buses to
simplify transport across the system. The DS21Q42 can be configured to allow each framer’s data and
signaling busses to be multiplexed into higher speed data and signaling busses eliminating external
hardware saving board space and cost.
The interleaved PCM bus option supports two bus speeds and interleave modes. The 4.096 MHz bus
speed allows two framers to share a common bus. The 8.192 MHz bus speed allows all four of the
DS21Q42’s framers to share a common bus. Framers can interleave their data either on byte or frame
boundaries. Framers that share a common bus must be configured through software and require several
device pins to be connected together externally (see figures 22-1 & 22-2). Each framer’s elastic stores
must be enabled and configured for 2.048 MHz operation. The signal RSYNC must be configured as an
input on each framer.
For all bus configurations, one framer will be configured as the master device and the remaining framers
on the shared bus will be configured as slave devices. Refer to the IBO register description below for
more detail. In the 4.096 MHz bus configuration there is one master and one slave per bus. Figure 22-1
shows the DS21Q42 configured to support two 4.096 MHz buses. Bus 1 consists of framers 0 and 1.
Bus 2 consists of framers 2 and 3. Framers 0 and 2 are programmed as master devices. Framers 1 and 3
are programmed as slave devices. In the 8.192 MHz bus configuration there is one master and three
slaves. Figure 22-2 shows the DS21Q42 configured to support a 8.192 MHz bus. Framers 0 is
programmed as the master device. Framers 1, 2 and 3 are programmed as slave devices. Consult timing
diagrams in section 24 for additional information.
When using the frame interleave mode, all framers that share an interleaved bus must have receive
signals (RPOS & RNEG) that are synchronous with each other. The received signals must originate
from the same clock reference. This restriction does not apply in the byte interleave mode.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21FT42N | IC FRAMER T1 4X3 12CH IND 300BGA |
| VE-24R-IX-S | CONVERTER MOD DC/DC 7.5V 75W |
| CONREVMCX003.062-L | CONN RPMCX FEM EDGE MT 0.062"EXT |
| PIC18F23K20-E/SP | IC PIC MCU FLASH 4KX16 28-DIP |
| CONREVSMA006.031 | CONN RPSMA FML EDGE MULTI 0.031" |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21FF42N+ | 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl T1/T1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21FF44 | 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21FF44N | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21FT40 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Four x Three 12 Channel E1 Framer |
| DS21FT40N | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。