參數資料
型號： DS2174Q+
廠商： Maxim Integrated Products
文件頁數： 10/24頁
文件大?。?/td> 0K
描述： IC BERT ENHANCED 44-PLCC
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 26
功能： 增強型位誤碼率測試器（EBERT）
接口： E1，J1，T1
電路數： 1
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 50mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
包括： 錯誤計數器，樣式發生器和檢測器
DS2174
18 of 24
4. RAM ACCESS
4.1 Indirect Addressing
512 bytes of memory, which is addressed indirectly, are available for repetitive patterns. Data bytes are
loaded one at a time into the indirect address register at address 0Fh. The RAM mode control bit, CR4.3,
determines the access to the RAM. If CR4.3 = 0, the RAM is under control of the BERT state machine. If
CR4.3 = 1, the RAM is under the control of the parallel port. This section discusses CR4.3 = 1.
The accompanying flow chart describes the algorithm used to write repetitive patterns to the RAM. The
programmer initializes a counter (n) to -1 in software, then sets CR4.3 and clears CR4.4. The rising edge
of CR4.3 resets the RAM address pointer to address 00h. Address 0Fh becomes the indirect access port to
the RAM. A write cycle on the parallel port to address 0Fh writes to the address in RAM pointed to by
the address pointer. The end of the write cycle, rising edge of WR, increments the address pointer. The
programmer then increments the counter (n) by 1 and loops until the pattern load is complete. Clear
CR4.3 to return control of the RAM to the BERT state machine. Finally, write the value in the counter (n)
back to address 04h and 05h to mark the last address of the pattern in memory.
The RAM contents can be verified by executing the same algorithm, replacing the parallel-port write with
a read, and setting CR4.4. CR4.3 must remain set for the entire algorithm to properly increment the
address pointer.
YES
WRITE n TO CR3
LAST BYTE?
DONE
CR4.3=1
CR4.4=0
n = -1
WRITE BYTE TO ADDRESS
0Fh
CR4.3 = 0
n = n + 1
START
NO
IF n > 255, THEN
SET CR4.0
相關PDF資料
PDF描述
DS21554LBN+ IC TXRX E1 5V 100-LQFP
DS21552LN+ IC TXRX T1 1-CHIP 5V 100-LQFP
DS2174Q+T&R IC BERT ENHANCED 44-PLCC
DS2155G+T&R IC TXRX T1/E1/J1 1 CHIP 100CSBGA
DS2155G+ IC TXRX T1/E1/J1 1-CHIP 100CSBGA
相關代理商/技術參數
參數描述
DS2174Q/T&R+ 制造商:Maxim Integrated Products 功能描述:BIT ERROR RATE TESTER 44PLCC - Tape and Reel
DS2174Q/T&R 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray
DS2174Q+ 功能描述:電信集成電路 Enhanced Bit Error Rate Tester (BERT) RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray
DS2174Q+T&R 制造商:Maxim Integrated Products 功能描述:BIT ERROR RATE TESTER 44PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC BERT ENHANCED 44-PLCC
DS2174Q+T&R 功能描述:電信集成電路 Enhanced Bit Error Rate Tester (BERT) RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*