山村最原始的肉欲伦情,撒尿正面bbw毛,中文字幕乱码一二三四区

您現在的位置：買賣IC網 > PDF目錄11005 > DS21352LN+ (Maxim Integrated Products)IC TXRX T1 1-CHIP 3.3V 100-LQFP PDF資料下載

參數資料

型號：	DS21352LN+
廠商：	Maxim Integrated Products
文件頁數：	128/137頁
文件大?。?/td>	0K
描述：	IC TXRX T1 1-CHIP 3.3V 100-LQFP
產品培訓模塊：	Lead (SnPb) Finish for COTS Obsolescence Mitigation Program
標準包裝：	90
功能：	單芯片收發器
接口：	HDLC，T1
電路數：	1
電源電壓：	3.14 V ~ 3.47 V
電流 - 電源：	75mA
工作溫度：	-40°C ~ 85°C
安裝類型：	表面貼裝
封裝/外殼：	100-LQFP
供應商設備封裝：	100-LQFP（14x14）
包裝：	托盤
包括：	DSX-1 和 CSU 線路補償發生器，HDLC 控制器，帶內回路代碼發生器和檢測器
產品目錄頁面：	1429 (CN2011-ZH PDF)

DS21352/DS21552

90 of 137

16.4 PROTECTED INTERFACES

In certain applications, such as connecting to the PSTN, it is required that the network interface be

protected from and resistant to certain electrical conditions. These conditions are divided into two

categories, surge and power line cross. A typical cause of surge is lightening strike. Power line cross

refers to accidental contact with high voltage power wiring. For protection against surges, additional

components and PCB layout considerations are required to reroute and dissipate this energy. In a surge

event, the network interface must not be damaged and continue to work after the event. In the event of a

power line contact, components such as fuses or PTCs that can “open” the circuit are required to prevent

the possibility of a fire caused by overheating the transformer. The circuit examples in this data sheet are

for “Secondary Over Voltage Protection” schemes for the line terminating equipment. Primary protection

is typically provided by the network service provide and is external to the equipment.

Figure 16-6 shows an example circuit for the 5 volt device and Figure 16-7 is an example for the 3.3

device. In both examples, fuses are used to provide protection against power line cross. 470 ohm input

resistors on the receive pair, a transient suppresser and a diode bridge on the transmit pair provide surge

protection. Resistors R1 – R4 provide surge protection for the fuse. Careful selection of the transformer

will allow the use of a fuse that requires no additional surge protection such as the circuit shown in Figure

16-7. The circuit shown in Figure 16-7 is required for 3.3 volt operation since additional resistance in the

transmit pair cannot be tolerated. For more information on line interface design, consult the T1 Line

Interface Design Criteria (note 353) and Secondary Over Voltage Protection (note 324) application notes.

These notes are available from Dallas Semiconductor’s web site.

相關代理商/技術參數	參數描述
DS21352LN+	功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354	制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3.3V/5V E1 Single-Chip Transceivers
DS21354DK	功能描述:網絡開發工具 DS21354 Dev Kit RoHS:否制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
DS21354G	功能描述:網絡控制器與處理器 IC RoHS:否制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354GN	功能描述:網絡控制器與處理器 IC RoHS:否制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray

發布緊急采購，3分鐘左右您將得到回復。

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

添加更多采購

<progress id="zikhv"></progress>