參數資料
型號： DS21352L
廠商： Maxim Integrated Products
文件頁數： 128/137頁
文件大?。?/td> 0K
描述： IC TXRX T1 1-CHIP 3.3V 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
產品變化通告： Product Discontinuation 20/Feb/2012
標準包裝： 90
功能： 單芯片收發器
接口： HDLC，T1
電路數： 1
電源電壓： 3.14 V ~ 3.47 V
電流 - 電源： 75mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（14x14）
包裝： 托盤
包括： DSX-1 和 CSU 線路補償發生器，HDLC 控制器，帶內回路代碼發生器和檢測器
DS21352/DS21552
90 of 137
16.4 PROTECTED INTERFACES
In certain applications, such as connecting to the PSTN, it is required that the network interface be
protected from and resistant to certain electrical conditions. These conditions are divided into two
categories, surge and power line cross. A typical cause of surge is lightening strike. Power line cross
refers to accidental contact with high voltage power wiring. For protection against surges, additional
components and PCB layout considerations are required to reroute and dissipate this energy. In a surge
event, the network interface must not be damaged and continue to work after the event. In the event of a
power line contact, components such as fuses or PTCs that can “open” the circuit are required to prevent
the possibility of a fire caused by overheating the transformer. The circuit examples in this data sheet are
for “Secondary Over Voltage Protection” schemes for the line terminating equipment. Primary protection
is typically provided by the network service provide and is external to the equipment.
Figure 16-6 shows an example circuit for the 5 volt device and Figure 16-7 is an example for the 3.3
device. In both examples, fuses are used to provide protection against power line cross. 470 ohm input
resistors on the receive pair, a transient suppresser and a diode bridge on the transmit pair provide surge
protection. Resistors R1 – R4 provide surge protection for the fuse. Careful selection of the transformer
will allow the use of a fuse that requires no additional surge protection such as the circuit shown in Figure
16-7. The circuit shown in Figure 16-7 is required for 3.3 volt operation since additional resistance in the
transmit pair cannot be tolerated. For more information on line interface design, consult the T1 Line
Interface Design Criteria (note 353) and Secondary Over Voltage Protection (note 324) application notes.
These notes are available from Dallas Semiconductor’s web site.
相關PDF資料
PDF描述
VI-B5K-IY-F1 CONVERTER MOD DC/DC 40V 50W
DS21554L IC TXRX E1 1-CHIP 5V 100-LQFP
VI-B5J-IY-F2 CONVERTER MOD DC/DC 36V 50W
VI-B5H-IY-F4 CONVERTER MOD DC/DC 52V 50W
VI-B5H-IY-F1 CONVERTER MOD DC/DC 52V 50W
相關代理商/技術參數
參數描述
DS21352L+ 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21352LB 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21352LB+ 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21352LBN 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS21352L-C02 功能描述:網絡控制器與處理器 IC T1 Single Chip Transceivers RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*