- 您現在的位置：買賣IC網 > PDF目錄379181 > DS1822-PAR Econo 1-Wire?? Parasite-Power Digital Thermometer PDF資料下載
參數資料
| 型號： | DS1822-PAR |
| 元件分類： | 溫度傳感器 |
| 英文描述： | Econo 1-Wire?? Parasite-Power Digital Thermometer |
| 文件頁數： | 9/19頁 |
| 文件大?。?/td> | 138K |
| 代理商： | DS1822-PAR |
DS1822-PAR
9 of 19
learns the ROM codes through a process of elimination that requires the master to perform a Search ROM
cycle (i.e., Search ROM command followed by data exchange) as many times as necessary to identify all
of the slave devices. If there is only one slave on the bus, the simpler Read ROM command (see below)
can be used in place of the Search ROM process. For a detailed explanation of the Search ROM
procedure, refer to the iButton Book of Standards at www.ibutton.com/ibuttons/standard.pdf. After every
Search ROM cycle, the bus master must return to Step 1 (Initialization) in the transaction sequence.
This command can only be used when there is one slave on the bus. It allows the bus master to read the slave’s 64-bit ROM code without using the Search ROM procedure. If this command is used when there
is more than one slave present on the bus, a data collision will occur when all the slaves attempt to
respond at the same time.
MATCH ROM [55h]
The match ROM command followed by a 64–bit ROM code sequence allows the bus master to address a
specific slave device on a multi-drop or single-drop bus. Only the slave that exactly matches the 64–bit
ROM code sequence will respond to the function command issued by the master; all other slaves on the
bus will wait for a reset pulse.
SKIP ROM [CCh]
The master can use this command to address all devices on the bus simultaneously without sending out
any ROM code information. For example, the master can make all DS1822-PARs on the bus perform
simultaneous temperature conversions by issuing a Skip ROM command followed by a Convert T [44h]
command. Note, however, that the Skip ROM command can only be followed by the Read Scratchpad
[BEh] command when there is one slave on the bus. This sequence saves time by allowing the master to
read from the device without sending its 64–bit ROM code. This sequence will cause a data collision on
the bus if there is more than one slave since multiple devices will attempt to transmit data simultaneously.
ALARM SEARCH [ECh]
The operation of this command is identical to the operation of the Search ROM command except that
only slaves with a set alarm flag will respond. This command allows the master device to determine if
any DS1822-PARs experienced an alarm condition during the most recent temperature conversion. After
every Alarm Search cycle (i.e., Alarm Search command followed by data exchange), the bus master must
return to Step 1 (Initialization) in the transaction sequence. Refer to the OPERATION – ALARM
SIGNALING section for an explanation of alarm flag operation.
DS1822-PAR FUNCTION COMMANDS
After the bus master has used a ROM command to address the DS1822-PAR with which it wishes to
communicate, the master can issue one of the DS1822-PAR function commands. These commands allow
the master to write to and read from the DS1822-PAR’s scratchpad memory, initiate temperature
conversions and determine the power supply mode. The DS1822-PAR function commands, which are
described below, are summarized in Table 4 and illustrated by the flowchart in Figure 10.
CONVERT T [44h]
This command initiates a single temperature conversion. Following the conversion, the resulting thermal
data is stored in the 2-byte temperature register in the scratchpad memory and the DS1822-PAR returns to
its low-power idle state. Within 10
μ
s (max) after this command is issued the master must enable a
strong pullup on the 1-wire bus for the duration of the conversion (t
conv
) as described in the PARASITE
POWER section.
WRITE SCRATCHPAD [4Eh]
This command allows the master to write 3 bytes of data to the DS1822-PAR’s scratchpad. The first data
byte is written into the T
H
register (byte 2 of the scratchpad), the second byte is written into the T
L
相關PDF資料 |
PDF描述 |
|---|---|
| DS1847-010 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847-050 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847B-010 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847B-050 | Dual Temperature-Controlled NV Variable Resistor |
| DS1847E-010 | Dual Temperature-Controlled NV Variable Resistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1822-PAR/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1822-PAR_07 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Econo 1-Wire Parasite-Power Digital Thermometer |
| DS1822-PAR+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer |
| DS1822-PAR+T&R | 功能描述:板上安裝溫度傳感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS-18-22-RS | 制造商:TE Connectivity 功能描述:Red sealed splice terminal,0.5-1.5sq.mm |
發布緊急采購，3分鐘左右您將得到回復。