參數資料
型號： DS1822-PAR
元件分類： 溫度傳感器
英文描述： Econo 1-Wire?? Parasite-Power Digital Thermometer
文件頁數： 8/19頁
文件大小： 138K
代理商： DS1822-PAR
DS1822-PAR
8 of 19
HARDWARE CONFIGURATION
cá êé=V=
TRANSACTION SEQUENCE
The transaction sequence for accessing the DS1822-PAR is as follows:
Step 1. Initialization
Step 2. ROM Command (followed by any required data exchange)
Step 3. DS1822-PAR Function Command (followed by any required data exchange)
It is very important to follow this sequence every time the DS1822-PAR is accessed, as the DS1822-PAR
will not respond if any steps in the sequence are missing or out of order. Exceptions to this rule are the
Search ROM [F0h] and Alarm Search [ECh] commands. After issuing either of these ROM commands,
the master must return to Step 1 in the sequence.
INITIALIZATION
All transactions on the 1-wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the
slave(s). The presence pulse lets the bus master know that slave devices (such as the DS1822-PAR) are
on the bus and are ready to operate. Timing for the reset and presence pulses is detailed in the
1-WIRE SIGNALING section.
ROM COMMANDS
After the bus master has detected a presence pulse, it can issue a ROM command. These commands
operate on the unique 64–bit ROM codes of each slave device and allow the master to single out a
specific device if many are present on the 1-wire bus. These commands also allow the master to
determine how many and what types of devices are present on the bus or if any device has experienced an
alarm condition. There are five ROM commands, and each command is 8 bits long. The master device
must issue an appropriate ROM command before issuing a DS1822-PAR function command. A
flowchart for operation of the ROM commands is shown in Figure 10.
SEARCH ROM [F0h]
When a system is initially powered up, the master must identify the ROM codes of all slave devices on
the bus, which allows the master to determine the number of slaves and their device types. The master
V
PU
4.7K
5 μA
Typ.
R
X
T
X
DS1822-PAR 1-WIRE PORT
100
MOSFET
T
X
R
X
R
X
= RECEIVE
T
X
= TRANSMIT
1-wire bus
DQ
Pin
V
PU
Micro-
processor
Strong
Pullup
相關PDF資料
PDF描述
DS1847-010 Dual Temperature-Controlled NV Variable Resistor
DS1847-050 Dual Temperature-Controlled NV Variable Resistor
DS1847B-010 Dual Temperature-Controlled NV Variable Resistor
DS1847B-050 Dual Temperature-Controlled NV Variable Resistor
DS1847E-010 Dual Temperature-Controlled NV Variable Resistor
相關代理商/技術參數
參數描述
DS1822-PAR/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1822-PAR_07 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Econo 1-Wire Parasite-Power Digital Thermometer
DS1822-PAR+T&R 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 1-WIRE 3PIN TO-92 - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG TO-92 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors 1-Wire Digital Thermometer
DS1822-PAR+T&R 功能描述:板上安裝溫度傳感器 1-Wire Digital Thermometer RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS-18-22-RS 制造商:TE Connectivity 功能描述:Red sealed splice terminal,0.5-1.5sq.mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*