參數資料
型號: DS1800
廠商: DALLAS SEMICONDUCTOR
元件分類: 模擬信號調理
英文描述: Dual Inverting Log Gain/Attenuator(雙路反相對數放大/衰減器)
中文描述: SPECIALTY ANALOG CIRCUIT, PDIP20
封裝: 0.300 INCH, DIP-20
文件頁數: 4/13頁
文件大?。?/td> 96K
代理商: DS1800
DS1800
032098 4/13
provide the opposite function; positioning the wiper(s)
closer to the INx terminals, thus providing gain.
Each of these control inputs are internally pulled–up via
a 50K
resistance. Additionally, these inputs require no
external components for debouncing or timing which
are provided internal to the part.
Contact closure is defined as the transition from a high
level to a low level on these input terminals. The
DS1800 interprets input pulse widths as the means of
controlling wiper movement. A single pulse input over
the PxA or PxG input terminals will cause the wiper to
move one position. A transition from high to low on
these inputs is considered the beginning of pulse activ-
ity or contact closure. The DS1800 has two timing
modes for controlling the speed at which pushbuttons
will operate. These modes are termed fast mode opera-
tion and slow mode operation.
In slow mode operation, a single pulse is defined as
being greater than 1 ms but lasting no longer than 0.8
seconds. Correspondingly, in fast mode operation, a
single pulse is defined as being greater than 50
μ
s but
lasting no longer than 0.8 second.
Repetitive pulsed inputs can be used to step through
each resistive position of the device in a relatively fast
manner. The timing requirements for repetitive pulsed
inputs is that pulses must be separated by a minimum
time of 1 ms for slow mode operation and 50
μ
s for fast
mode operation.
Pulse inputs lasting longer than 0.8 seconds will cause
the wiper to move one position every 25 ms seconds
after the initial 0.8 second hold time. This is true regard-
less of the mode input. The total time required to tran-
scend the entire potentiometer using a continuous input
pulse is given by the following formula:
0.8(seconds) + 127 x 25 ms = 3.975(seconds)
SLOW MODE AND FAST MODE OPERATION
Pushbutton operation, as mentioned, can be operated
at two distinct speeds or modes; fast and slow. The
mode or speed of pushbutton debounce is determined
at device power–up by the state of the MODE pin. When
MODE powers to a high–state, pushbutton debounce
timing will operate at the slow mode rate. When pow-
ered and in the low–state, debounce timing operates at
the fast rate. Timing specifications for pushbutton
operation can be found in the AC Electrical Specification
Table for pushbutton operation. Timing diagrams for
push–button operation can be found in Figure 7.
ZERO CROSSING DETECTION
The DS1800 provides a zero–crossing detection capa-
bility when using the 3–Wire serial interface. Zero–
crossing detection provides a means for minimizing
unwanted audible noise that may result from sizable dis-
crete wiper transitions when using the part in audio
applications. The zero crossing detect feature allows
independent wiper changes only when the two termi-
nals of the potentiometer(s) have equal potentials and
within a 50 ms time window from the fall of the RST sig-
nal. If at 50 ms the DS1800 has not detected a zero
crossing, the wiper position of the potentiometer(s) will
change regardless of the state of the input signal. Zero–
crossing detection is activated when the ZCEN input is
in a low–state. When high, the ZCEN input deactivates
both the 50 ms time requirement and zero–detection
crossing.
Zero crossing detection is also available when using the
part in push–button operation. When a push–button is
activated, the part will change wiper position during the
first detected zero–crossing or at the end of a 50 ms time
window.
When operating in push–button operation with a contin-
uous input pulse, the wiper position will change once
during the initial 0.8 second time period. This change is
dictated by a detected zero–crossing or 50 ms time win-
dow. Subsequent changes when operating with a con-
tinuous input pulse occur on 25 ms time intervals and
are dependent on zero crossings or 50 ms time–outs.
MUTE CONTROL
The DS1800 provides a mute control feature which can
be accessed by the user through hardware or software.
Hardware control of the device is achieved through the
MUTE input pin. This pin is internally pulled up through
a 50K resistor and functions like the PxG and PxA push-
button controls. When this input is driven low, the wiper
outputs of both potentiometers will be internally con-
nected to the OUTx terminal of their respective poten-
tiometers. This input performs as a toggle input, with the
first activity on this pin connecting the wiper terminals to
the OUTx terminals (position 128) of the potentiometer.
The next input activity on this pin will return the wiper
position to the previous state before muting occurred.
相關PDF資料
PDF描述
DS1801 Dual Audio Taper Potentiometer(雙路音頻抽頭電位器)
DS1802 Dual Audio Taper Potentiometer with Push Button Control(帶按鈕控制的雙路音頻抽頭電位器)
DS1803 Addressable Dual Digital Potentiometer(可尋址雙路數字電位器)
DS1804 NV Trimmer Potentiometer(非易失性微調電位器)
DS1806 Digital Sextet Potentiometer(數字六位電位器)
相關代理商/技術參數
參數描述
DS1800-3 功能描述:線性和開關式電源 12V output, 1800W 1U x 4.2" x 11" RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
DS1801 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1801+ 功能描述:數字電位計 IC Dual Audio Taper Potentiometer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1801E 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Audio Taper Potentiometer
DS1801E-014 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel