參數資料
型號: DS1800
廠商: DALLAS SEMICONDUCTOR
元件分類: 模擬信號調理
英文描述: Dual Inverting Log Gain/Attenuator(雙路反相對數放大/衰減器)
中文描述: SPECIALTY ANALOG CIRCUIT, PDIP20
封裝: 0.300 INCH, DIP-20
文件頁數: 3/13頁
文件大?。?/td> 96K
代理商: DS1800
DS1800
032098 3/13
MODE
– Push–button Debounce Control. The MODE
pin is used to choose between a fast and slow mode of
push–button debouncing. When in a high state, push–
button debounce is slow. When in a low–state, push–
button debounce is faster. These timing differences are
discussed in the section entitled “Push–button Inter-
face Control”. The state of this pin is determined only at
device power–up.
POWER–UP CONDITIONS
The position of the wipers of the DS1800 on power up
are internally set to position 127, which is the last posi-
tion before mute. The user then has the responsibility of
changing the wiper position to the desired attenuation/
gain levels.
Additionally, the serial port is stable and active within 10
microseconds. The contact closure control interface
inputs are active after 50 ms.
INTERFACE CONTROL OPTIONS
Control of the DS1800 is provided via two types of inter-
face ports. A 3–wire CPU control interface allows the
exact wiper positions of the potentiometers to be written
using two 8–bit words. A cascade output, C
OUT
, is pro-
vided when controlling multiple devices via one CPU or
when reading the wiper positions of each potentiometer.
The second interface is a contact closure interface that
allows push–buttons to control movement of the wiper
positions. Under push–button control no external
debounce or timing circuitry is needed. A block diagram
of the DS1800 is shown in Figure 1.
3–WIRE SERIAL INTERFACE CONTROL
CPU control of the DS1800 is accomplished using the
3–Wire serial port of the device. This interface drives an
internal control logic unit. Direct wiper positioning is
accomplished by using this port which consist of three
input signals: RST, CLK, and D.
The RST control signal is used to enable 3–wire serial
port write operations. The CLK terminal is an input that
provides synchronization for data I/O. Data is input bit
by bit via the D input signal pin.
The 3–Wire serial timing diagrams are provided in
Figure 5. Serial port operation or activity begins with the
transition of the RST signal from a low–state to a high–
state. Once activated, data is clocked into the part on
the low to high transition of the CLK signal input. Data
input via the D terminal is transferred in order of the
desired potentiometer–0 wiper value, followed by the
potentiometer–1 wiper position value.
Two 8–bit values are used to store wiper position for
each potentiometer during powered conditions. These
8–bit values are written to a 16–bit I/O shift register. A
detailed diagram of the 16–bit I/O shift register is shown
in Figure 6.
Bits 0 through 7 are reserved for the positioning of
wiper–0 while bits 8 through 15 are reserved for control
of wiper–1. Bits 0 through 6 are used for actual wiper
positioning of potentiometer–0. Bit 7 is used to mute
potentiometer–0. If this bit is set to a “1”, the potentiom-
eter–0 wiper will be connected to the OUT0 end of the
resistor array regardless of the settings of bits 0
through 6.
Bits 8 through 15 are used for positioning the wiper of
potentiometer–1. Bits 8 through 14 control wiper posi-
tion on the resistor array. Bit 15 is used for muting poten-
tiometer–1. Bit 15, like bit 7, when set to “1” will mute
potentiometer 1, regardless of the settings of bits 8
through 14.
Data is transmitted LSB first starting with bit–0. A com-
plete transmission of 16 bits of data is required to insure
proper setting of each potentiometer’s wiper. An incom-
plete transmission may result in undesired wiper
settings.
Once the 16 bits of information has been transmitted
and the RST signal input transitions to a low–state, the
new wiper positions are loaded into the part.
PUSH–BUTTON INTERFACE CONTROL
The DS1800 can be configured to operate from contact
closure or push–button inputs. The push–button inputs
consist of signals P0A, P0G, P1A, P1G and MUTE.
P0A and P0G allow attenuation and gain control of the
input signal to potentiometer–0, while P1A and P1G
provide the same control for potentiometer–1. The
MUTE input provides a toggle control for muting the
potentiometers via pushbutton.
The P0A and P1A control inputs, based on the recom-
mended circuit configuration, are used to attenuate the
incoming signal by moving the wiper position towards
the OUTx terminals. The P0G and P1G control inputs
相關PDF資料
PDF描述
DS1801 Dual Audio Taper Potentiometer(雙路音頻抽頭電位器)
DS1802 Dual Audio Taper Potentiometer with Push Button Control(帶按鈕控制的雙路音頻抽頭電位器)
DS1803 Addressable Dual Digital Potentiometer(可尋址雙路數字電位器)
DS1804 NV Trimmer Potentiometer(非易失性微調電位器)
DS1806 Digital Sextet Potentiometer(數字六位電位器)
相關代理商/技術參數
參數描述
DS1800-3 功能描述:線性和開關式電源 12V output, 1800W 1U x 4.2" x 11" RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓(通道 1):20 V 輸出電流(通道 1):40 A 商用/醫用: 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:Rack 長度: 寬度: 高度:
DS1801 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1801+ 功能描述:數字電位計 IC Dual Audio Taper Potentiometer RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1801E 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Audio Taper Potentiometer
DS1801E-014 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel