- 您現在的位置：買賣IC網 > PDF目錄385272 > DS17487 (Maxim Integrated Products, Inc.) 3 Volt/5 Volt Real Time Clock(3V/5V實時時鐘) PDF資料下載
參數資料
| 型號： | DS17487 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 3 Volt/5 Volt Real Time Clock(3V/5V實時時鐘) |
| 文件頁數： | 6/32頁 |
| 文件大?。?/td> | 236K |
| 代理商： | DS17487 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS17485/DS17487
030598 6/32
DS17485 REAL TIME CLOCK ADDRESS MAP
Figure 2
0
00H
13
14
0DH
0EH
0
1
2
3
4
5
6
7
8
9
10
11
12
13
SECONDS
SECONDS ALARM
MINUTES
MINUTES ALARM
HOURS
HOURS ALARM
DAY OF THE WEEK
DAY OF THE MONTH
MONTH
YEAR
REGISTER A
REGISTER B
REGISTER C
REGISTER D
B
07FH
127
CLOCK/
14 BYTES
BANK 1
REGISTERS,
RAM
63
64
03FH
040H
50 BYTES
USER RAM
TIME, CALENDAR AND ALARM LOCATIONS
The time and calendar information is obtained by read-
ing the appropriate register bytes shown in Table 1. The
time, calendar, and alarm are set or initialized by writing
the appropriate register bytes. The contents of the time,
calendar, and alarm registers can be either Binary or
Binary–Coded Decimal (BCD) format. Table 1 shows
the binary and BCD formats of the twelve time, calendar,
and alarm locations that reside in both bank 0 and in
bank 1, plus the two extended registers that reside in
bank 1 only (bank 0 and bank 1 switching will be
explained later in this text).
Before writing the internal time, calendar, and alarm reg-
isters, the SET bit in Register B should be written to a
logic one to prevent updates from occurring while
access is being attempted. Also at this time, the data
format (binary or BCD), should be set via the data mode
bit (DM) of Register B. All time, calendar, and alarm reg-
isters must use the same data mode. The set bit in Reg-
ister B should be cleared after the data mode bit has
been written to allow the real-time clock to update the
time and calendar bytes.
Once initialized, the real–time clock makes all updates
in the selected mode. The data mode cannot be
changed without reinitializing the ten data bytes. The
24/12 bit cannot be changed without reinitializing the
hour locations. When the 12–hour format is selected,
the high order bit of the hours byte represents PM when
it is a logic one. The time, calendar, and alarm bytes are
always accessible because they are double buffered.
Once per second the ten bytes are advanced by one
second and checked for an alarm condition. If a read of
the time and calendar data occurs during an update, a
problem exists where seconds, minutes, hours, etc.
may not correlate. The probability of reading incorrect
time and calendar data is low. Several methods of
avoiding any possible incorrect time and calendar reads
are covered later in this text.
The four alarm bytes can be used in two ways. First,
when the alarm time is written in the appropriate hours,
minutes, and seconds alarm locations, the alarm inter-
rupt is initiated at the specified time each day if the alarm
enable bit is high . The second use condition is to insert
a “don’t care” state in one or more of the four alarm
bytes. The “don’t care” code is any hexadecimal value
from C0 to FF. The two most significant bits of each byte
set the “don’t care” condition when at logic 1. An alarm
will be generated each hour when the “don’t care” bits
are set in the hours byte. Similarly, an alarm is gener-
ated every minute with “don’t care” codes in the hours
and minute alarm bytes. The “don’t care” codes in all
three alarm bytes create an interrupt every second. The
three alarm bytes may be used in conjunction with the
date alarm as described in the Wakeup/Kickstart sec-
tion. The century counter will be discussed later in this
text.
相關PDF資料 |
PDF描述 |
|---|---|
| DS17485 | 3 Volt/5 Volt Real Time Clock(3V/5V實時時鐘) |
| DS1775 | SOT23 Digital Thermometer and Thermostat(SOT23數字溫度計和恒溫控制器) |
| DS1800 | Dual Inverting Log Gain/Attenuator(雙路反相對數放大/衰減器) |
| DS1801 | Dual Audio Taper Potentiometer(雙路音頻抽頭電位器) |
| DS1802 | Dual Audio Taper Potentiometer with Push Button Control(帶按鈕控制的雙路音頻抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS17487-3 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17487-3+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17487-3IND | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17487-3IND+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS174875 | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。