- 您現在的位置：買賣IC網 > PDF目錄385272 > DS17487 (Maxim Integrated Products, Inc.) 3 Volt/5 Volt Real Time Clock(3V/5V實時時鐘) PDF資料下載
參數資料
| 型號： | DS17487 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 3 Volt/5 Volt Real Time Clock(3V/5V實時時鐘) |
| 文件頁數： | 15/32頁 |
| 文件大小： | 236K |
| 代理商： | DS17487 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS17485/DS17487
030598 15/32
tion, the kickstart feature can allow the system to be
powered up in response to a low going transition on the
KS pin, without operating voltage applied to the V
CC
pin.
As a result, system power may be applied upon such
events as a key closure, or modem ring detect signal. In
order to use either the wake up or the kickstart features,
the DS17485/DS17487 must have an auxiliary battery
connected to the V
BAUX
pin and the oscillator must be
running and the countdown chain must not be in reset
(Register A DV2, DV1, DV0 = 01X). If DV2, DV1, and
DV0 are not in this required state, the PWR pin will not
be driven low in response to a kickstart or wakeup condi-
tion, while in battery-backed mode.
The wake up feature is controlled through the Wake up
Interrupt Enable bit in extended control register 4B
(WIE, bank 1, 04BH). Setting WIE to 1 enables the
wake up feature, clearing WIE to 0 disables it. Similarly,
the kickstart feature is controlled through the Kickstart
Interrupt Enable bit in extended control register 4B
(KSE, bank 1, 04BH).
A wake up sequence will occur as follows: When wake
up is enabled via WIE = 1 while the system is powered
down (no V
CC
voltage), the clock/calendar will monitor
the current date for a match condition with the date
alarm register (bank 1, register 049H). In conjunction
with the date alarm register, the hours, minutes, and
seconds alarm bytes in the clock/calendar register map
(bank 0, registers 05H, 03H, and 01H) are also moni-
tored. As a result, a wake up will occur at the date and
time specified by the date, hours, minutes, and seconds
alarm register values. This additional alarm will occur
regardless of the programming of the AIE bit (bank 0,
register B, 0BH). When the match condition occurs, the
PWR pin will automatically be driven low. This output
can be used to turn on the main system power supply
which provides V
CC
voltage to the DS17485/DS17487
as well as the other major components in the system.
Also at this time, the Wake Up flag (WF, bank 1, register
04AH) will be set, indicating that a wake up condition
has occurred.
A kickstart sequence will occur when kickstarting is
enabled via KSE = 1. While the system is powered
down, the KS input pin will be monitored for a low going
transition of minimum pulse width t
KSPW
. When such a
transition is detected, the PWR line will be pulled low, as
it is for a wake up condition. Also at this time, the Kick-
start Flag (KF, bank 1, register 04AH) will be set, indicat-
ing that a kickstart condition has occurred.
The timing associated with both the wake up and kick-
starting sequences is illustrated in the Wake Up / Kick-
start Timing Diagram in the Electrical Specifications
section of this data sheet. The timing associated with
these functions is divided into 5 intervals, labeled 1–5 on
the diagram.
The occurrence of either a kickstart or wake up condi-
tion will cause the PWR pin to be driven low, as
described above. During interval 1, if the supply voltage
on the DS17485/DS17487 V
CC
pin rises above the 3
volt power fail level before the power on timeout period
(t
POTO
) expires, then PWR will remain at the active low
level. If V
CC
does not rise above the 3 volt power fail
voltage in this time, then the PWR output pin will be
turned off and will return to its high impedance level. In
this event, the IRQ pin will also remain tri–stated. The
interrupt flag bit (either WF or KF) associated with the
attempted power on sequence will remain set until
cleared by software during a subsequent system
power on.
If V
CC
is applied within the timeout period, then the sys-
tem power on sequence will continue as shown in inter-
vals 2–5 in the timing diagram. During interval 2, PWR
will remain active and IRQ will be driven to its active low
level, indicating that either WF or KF was set in initiating
the power on. In the diagram KS is assumed to be pulled
up to the V
BAUX
supply. Also at this time, the PAB bit will
be automatically cleared to 0 in response to a success-
ful power on. The PWR line will remain active as long as
the PAB remains cleared to 0.
At the beginning of interval 3, the system processor has
begun code execution and clears the interrupt condition
of WF and/or KF by writing zeroes to both of these con-
trol bits. As long as no other interrupt within the
DS17485/DS17487 is pending, the IRQ line will be
taken inactive once these bits are reset. Execution of
the application software may proceed. During this time,
both the wake up and kickstart functions may be used to
generate status and interrupts. WF will be set in
response to a date, hours, minutes, and seconds match
condition. KF will be set in response to a low going tran-
sition on KS. If the associated interrupt enable bit is set
(WIE and/or KSE) then the IRQ line will driven active low
in response to enabled event. In addition, the other pos-
sible interrupt sources within the DS17485/DS17487
may cause IRQ to be driven low. While system power is
applied, the on chip logic will always attempt to drive the
PWR pin active in response to the enabled kickstart or
wake up condition. This is true even if PWR was pre-
相關PDF資料 |
PDF描述 |
|---|---|
| DS17485 | 3 Volt/5 Volt Real Time Clock(3V/5V實時時鐘) |
| DS1775 | SOT23 Digital Thermometer and Thermostat(SOT23數字溫度計和恒溫控制器) |
| DS1800 | Dual Inverting Log Gain/Attenuator(雙路反相對數放大/衰減器) |
| DS1801 | Dual Audio Taper Potentiometer(雙路音頻抽頭電位器) |
| DS1802 | Dual Audio Taper Potentiometer with Push Button Control(帶按鈕控制的雙路音頻抽頭電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS17487-3 | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17487-3+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17487-3IND | 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS17487-3IND+ | 功能描述:實時時鐘 3V/5V RTC RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| DS174875 | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。