- 您現在的位置：買賣IC網 > PDF目錄379175 > DRV102T PWM SOLENOID/VALVE DRIVER PDF資料下載
參數資料
| 型號： | DRV102T |
| 英文描述： | PWM SOLENOID/VALVE DRIVER |
| 中文描述： | 脈寬調制電磁/閥驅動 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 253K |
| 代理商： | DRV102T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
11
DRV102
STATUS FLAG
Flag (pin 7) provides fault indication for under-current,
over-current, and thermal shutdown conditions. During a
fault condition, Flag output is driven low (pin voltage
typically drops to 0.2V). A pull-up resistor, as shown in
Figure 7, is required to interface with standard logic. A small
value capacitor may be needed between Flag and ground in
noisy applications.
Figure 7 gives an example of a non-latching fault monitoring
circuit, while Figure 8 provides a latching version. The Flag
pin can sink several milliamps, sufficient to drive external
logic circuitry or an LED (Figure 9) to indicate when a fault
has occurred. In addition, the Flag pin can be used to turn off
other DRV102’s in a system for chain fault protection.
Over/Under Current Fault
An over-current fault occurs when the output current ex-
ceeds the current limit. All units are guaranteed to drive 2A
without current limiting. Typically, units will limit at 2.7A.
The status flag is not latched. Since current during PWM
mode is switched on and off, the flag output will be modu-
lated with PWM timing (see flag waveforms in the Typical
Performance Curves).
An under-current fault occurs when the output current is
below the under-scale current threshold (typically 16mA).
For example, this function indicates when the load is discon-
nected. Again, the flag output is not latched, so an under-
current condition during PWM mode will produce a flag
output that is modulated by the PWM waveform. An initial,
brief under-current flag normally appears driving inductive
loads and may be avoided by adding a parallel resistor
sufficient to move the initial current above the under-current
threshold. Avoid adding capacitance to pin 6 (Out) as it may
cause momentary current limiting.
Over-Temperature Fault
A thermal fault occurs when the die reaches approximately
165
°
C, producing a similar effect as pulling the input low.
Internal shutdown circuitry disables the output and resets the
Delay Adjust pin. The Flag is latched in the low state (fault
condition) until the die has cooled to approximately 150
°
C.
A thermal fault can occur in any mode of operation. Recov-
ery from thermal fault will start in delay mode (constant dc
output).
FIGURE 8. Latching Fault Monitoring Circuit.
FIGURE 7. Non-Latching Fault Monitoring Circuit.
DRV102
Thermal Shutdown
Over/Under Current
6
5
7
V
S
Out
4
Gnd
5k
Pull-Up
+5V
Flag
TTL or HCT
DRV102
Thermal Shutdown
Over/Under Current
5
7
6
20k
+5V
Flag
Q
Q
CLR
Flag
Flag
Flag Reset
J
CLK
GND
K
V
S
74XX76A
(1)
NOTE: (1) Small capacitor (10pF) may be required in noisy environments.
4
Gnd
V
S
Out
FIGURE 9. LED to Indicate Fault Condition.
DRV102
Thermal Shutdown
Over/Under Current
7
5k
+5V
Flag
(LED)
HLMP-Q156
5
6
4
Gnd
V
S
Out
相關PDF資料 |
PDF描述 |
|---|---|
| DRV1100 | HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER |
| DRV1100P | HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER |
| DRV1100U | HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER |
| DS-112PIN | Four-Way Power Dividers 10 - 500 MHz |
| DS-112312 | Four-Way Power Dividers 10 - 500 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DRV102T | 制造商:BURR-BROWN 功能描述:SOLENOID/VALVE DRIVER PWM TO-220-7 |
| DRV102TG3 | 功能描述:馬達/運動/點火控制器和驅動器 PWM Solenoid/Valve Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| DRV103 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:PWM LOW-SIDE DRIVER (1.5A and 3A) for Solenoids, Coils, Valves, Heaters, and Lamps |
| DRV103H | 功能描述:馬達/運動/點火控制器和驅動器 Low Side Driver 1.5A/3A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| DRV103H | 制造商:Texas Instruments 功能描述:PWM LOW SIDE DRIVER 1.5A/3A HSOP8 |
發布緊急采購，3分鐘左右您將得到回復。