- 您現在的位置：買賣IC網 > PDF目錄379137 > DEM-DSP102 DEM-DSP102 - DISCONTINUED PRODUCT. No longer recommended for new design. PDF資料下載
參數資料
| 型號： | DEM-DSP102 |
| 英文描述： | DEM-DSP102 - DISCONTINUED PRODUCT. No longer recommended for new design. |
| 中文描述： | 馬克- DSP102 -已停產產品。不再推薦用于新設計。 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 194K |
| 代理商： | DEM-DSP102 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
6
DEM-DAI
DIGITAL AUDIO TRANSMITTER FLAGS
Switch SW9 is a DIP switch used to setup additional digital
audio transmitter options. Figure 4 shows an illustration of
SW9, with each switch labeled with its appropriate designa-
tor. The following paragraphs explains the function of each
of the DIP switch segments.
The PRO switch is used to select Consumer or Professional
mode. Set this switch HIGH for Consumer mode, and LOW
for Professional mode. This pin should also be set LOW
when using the transmitter in Transparent mode.
The PRO switch selection, either Consumer or Professional,
defines the function of the next seven switches. For most
DEM-DAI applications, set the mode to Consumer (PRO =
HIGH). Only the consumer definitions are given here. Con-
sult the CS8402A data sheet for information regarding the
Professional mode definitions.
FC0 and FC1, corresponding to channel status bits 24 and
25, denote the sampling frequency. Table IV shows the
switch settings and their corresponding selections.
FC0
FC1
SAMPLING FREQUENCY
0
0
1
1
0
1
0
1
44.1kHz
48kHz
32kHz
44.1kHz (CD submode)
TABLE IV. Sampling Frequency Flag Settings.
The remaining five switches correspond to channel status bit
selections. C2, C3, C8,C9, and C15 correspond to channel
status bits 2, 3, 8, 9, and 15. Consult the AES specification
or the CS8402A data sheet for the definition of these bits in
Consumer and Professional modes.
JUMPERS
There are six jumpers that are used to setup clocking
options. They are described in the following paragraphs.
JP1 is used to select the system clock source. Figure 5 shows
the header block with descriptions for each of the three
options.
FIGURE 5. System Clock Source Selection.
JP2 is used to select the bit clock (BCK) source. Figure 6
shows the header block with descriptions for each of the four
options. Regardless of the BCK source selected, the bit
clock rate will be 64 f
S
.
FIGURE 6. Bit Clock Source Selection.
FIGURE 4. Digital Audio Transmitter Status Bit Switch.
SW9
L
H
C9
C8
C15
C2
C3
FC0
FC1
PR0
Channel
Status
Bit
Selection
H = Consumer Mode
L = Professional Mode
In consumer mode, these correspond to channel status
bits 24 and 25, which denote the sampling frequency.
JP1
INV
NML
XTAL
Inverted output clock from digital audio receiver
Normal output clock from digital audio receiver
Use crystal oscillator/divider as system clock
JP2
DIR
512
384
256
BCK generated by digital audio receiver
BCK from crystal oscillator/divider, system clock = 512 f
S
BCK from crystal oscillator/divider, system clock = 384 f
S
BCK from crystal oscillator/divider, system clock = 256 f
S
NOTE: Regardless of selection, BCK = 64 f
S
相關PDF資料 |
PDF描述 |
|---|---|
| DEM-OPA68XU | EVALUATION FIXTURE |
| DEM-PCM1702 | DEM-PCM1702 - EVALUATION FIXTURE |
| DEM-PCM1704 | DEM-PCM1704 - EVALUATION FIXTURE |
| DEM-PCM1710 | DEM-PCM1710 - EVALUATION FIXTURE |
| DEM-PCM1760 | DEM-PCM1760 - EVALUATION FIXTURE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEME3100JA5N00 | 制造商:KEMET Corporation 功能描述:FILM CAP 33NF 5% SMD - Tape and Reel |
| DEME-5W1P | 制造商:ITT Interconnect Solutions 功能描述:DEME-5W1P - Bulk |
| DEME5W1PK127 | 制造商:ITT Interconnect Solutions 功能描述:DEME-5W1P-K127 / 053516-0857 / D SUB |
| DEME5W1PK87 | 制造商:ITT Interconnect Solutions 功能描述:CONN DSUB PLUG 5W1 SLDER CUP 制造商:ITT Interconnect Solutions 功能描述:Conn Combo D-Subminiature PIN 4Signal/1Cavity POS Solder Pot ST 5 Terminal 1 Port |
| DEME-5W1P-K87 | 功能描述:CONN DSUB PLUG 5W1 SLDER CUP RoHS:是 類別:連接器，互連式 >> D-Sub 系列:Combo D®, D*M 標準包裝:1 系列:Combo D®, D*M 連接器類型:D-Sub，組合式 位置數:11 行數:2 外殼尺寸，連接器布局:2（DA，A）- 11C1，11W1 觸點類型：:信號和同軸或電源（未包括） 連接器類型:插頭，公引腳 安裝類型:面板安裝 法蘭特點:體座/外殼（無螺紋） 端子:焊杯 特點:屏蔽 外殼材料，表面處理:鋼，鍍鎘 觸點表面涂層:金 觸點涂層厚度:閃光 防護等級:- 工作溫度:-55°C ~ 125°C 額定電壓:- 額定電流:7.5A 體座材料:聚酯 顏色:黑 其它名稱:IDAM11W1PA101 |
發布緊急采購，3分鐘左右您將得到回復。