- 您現在的位置：買賣IC網 > PDF目錄17065 > DC790A (Linear Technology)BOARD DELTA SIGMA ADC LTC2439-1 PDF資料下載
參數資料
| 型號： | DC790A |
| 廠商： | Linear Technology |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2439-1 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC790A Design File DC790A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.8 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2439-1 |
| 已供物品： | 板 |
| 相關產品： | LTC2439-1CGN#PBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#PBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN#TRPBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#TRPBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#TR-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN#TR-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2439-1
12
24391fa
(Bit 18) for the next conversion cycle. Table 3 summarizes
the output data format.
In order to remain compatible with some SPI
microcontrollers, more than 19 SCK clock pulses may be
applied. As long as these clock pulses are complete before
the conversion ends, they will not effect the serial data.
However, switching SCK during a conversion may gener-
ate ground currents in the device leading to extra offset
and noise error sources.
As long as the voltage applied to any channel (CH0-CH15,
COM) is maintained within the – 0.3V to (VCC + 0.3V)
absolute maximum operating range, a conversion result is
generated for any differential input voltage VIN from
–FS = – 0.5 VREF to +FS = 0.5 VREF. For differential input
voltages greater than +FS, the conversion result is clamped
to the value corresponding to the +FS + 1LSB. For differ-
ential input voltages below –FS, the conversion result is
clamped to the value corresponding to –FS – 1LSB.
Simultaneous Frequency Rejection
The LTC2439-1 internal oscillator provides better than
87dB normal mode rejection over the range of 49Hz to
61.2Hz as shown in Figure 4. For simultaneous 50Hz/60Hz
rejection using the internal oscillator, FO should be con-
nected to GND.
When a fundamental rejection frequency different from
the range 49Hz to 61.2Hz is required or when the converter
must be synchronized with an outside source, the
APPLICATIO S I FOR ATIO
WU
UU
LTC2439-1 can operate with an external conversion clock.
The converter automatically detects the presence of an
external clock signal at the FO pin and turns off the internal
oscillator. The frequency fEOSC of the external signal must
be at least 2560Hz to be detected. The external clock signal
duty cycle is not significant as long as the minimum and
maximum specifications for the high and low periods, tHEO
and tLEO, are observed.
While operating with an external conversion clock of a
frequency fEOSC,theLTC2439-1providesbetterthan110dB
normal mode rejection in a frequency range fEOSC/2560
±4%. The normal mode rejection as a function of the input
frequency deviation from fEOSC/2560 is shown in Figure 5.
Whenever an external clock is not present at the FO pin the
converter automatically activates its internal oscillator and
enters the Internal Conversion Clock mode. The LTC2439-1
operation will not be disturbed if the change of conversion
clock source occurs during the sleep state or during the data
output state while the converter uses an external serial clock.
If the change occurs during the conversion state, the result
of the conversion in progress may be outside specifications
but the following conversions will not be affected. If the
change occurs during the data output state and the con-
verter is in the Internal SCK mode, the serial clock duty cycle
may be affected but the serial data stream will remain valid.
Table 4 summarizes the duration of each state and the
achievable output data rate as a function of FO.
Figure 4. LTC2439-1 Normal Mode Rejection
When Using an Internal Oscillator
48
50
52
54
56
58
60
62
DIFFERENTIAL INPUT SIGNAL FREQUENCY (Hz)
NORMAL
MODE
REECTION
RATIO
(dB)
24391 F04a
–80
–90
–100
–120
–130
–140
Figure 5. LTC2439-1 Normal Mode Rejection When
Using an External Oscillator of Frequency fEOSC
DIFFERENTIAL INPUT SIGNAL FREQUENCY
DEVIATION FROM NOTCH FREQUENCY fEOSC/2560(%)
–12
–8
–4
048
12
NORMAL
MODE
REJECTION
(dB)
24361 F04b
–80
–85
–90
–95
–100
–105
–110
–115
–120
–125
–130
–135
–140
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD5535EBZ | BOARD EVALUATION FOR AD5535 |
| SDR0403-390KL | INDUCTOR POWER 39UH 0.59A 0403 |
| EBA22DRMD | CONN EDGECARD 44POS .125 SQ WW |
| EVAL-AD5757SDZ | BOARD EVAL FOR AD5757 |
| EVAL-AD5760SDZ | BOARD EVAL FOR AD5760SDZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC798B | 功能描述:BOARD DELTA SIGMA ADC LTC2480 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC-7G3EWA | 制造商:Kingbright Corporation 功能描述:Red/Green 10-seg LED lightbar, DC-7G3EWA |
| DC7G3HWA | 功能描述:LED條和陣列 7GR 3RED BARGRAFT 10 SEGMENT RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| DC-7G3HWA | 制造商:Kingbright Corporation 功能描述: |
| DC7K67J/4LR61 | 制造商:Duracell 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。