- 您現在的位置：買賣IC網 > PDF目錄17065 > DC790A (Linear Technology)BOARD DELTA SIGMA ADC LTC2439-1 PDF資料下載
參數資料
| 型號： | DC790A |
| 廠商： | Linear Technology |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2439-1 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC790A Design File DC790A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.8 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2439-1 |
| 已供物品： | 板 |
| 相關產品： | LTC2439-1CGN#PBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#PBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN#TRPBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#TRPBF-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1IGN#TR-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP LTC2439-1CGN#TR-ND - IC ADC 16BIT 16CH MCRPWR 28SSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2439-1
20
24391fa
Digital Signal Levels
The LTC2439-1’s digital interface is easy to use. Its digital
inputs (SDI, FO, CS and SCK in External SCK mode of
operation) accept standard TTL/CMOS logic levels and the
internal hysteresis receivers can tolerate edge rates as slow
as 100
s. However, some considerations are required to
take advantage of the accuracy and low supply current of
this converter.
The digital output signals (SDO and SCK in Internal SCK
mode of operation) are less of a concern because they are
not generally active during the conversion state.
While a digital input signal is in the range 0.5V to
(VCC – 0.5V), the CMOS input receiver draws additional
current from the power supply. It should be noted that,
when any one of the digital input signals (SDI, FO, CS and
SCK in External SCK mode of operation) is within this
range, the power supply current may increase even if the
signal in question is at a valid logic level. For micropower
operation, it is recommended to drive all digital input
signals to full CMOS levels [VIL < 0.4V and
VOH > (VCC – 0.4V)].
During the conversion period, the undershoot and/or
overshoot of a fast digital signal connected to the pins
may severely disturb the analog to digital conversion
process. Undershoot and overshoot can occur because of
the impedance mismatch at the converter pin when the
transition time of an external control signal is less than
twice the propagation delay from the driver to LTC2439-
1. For reference, on a regular FR-4 board, signal propaga-
tion velocity is approximately 183ps/inch for internal
traces and 170ps/inch for surface traces. Thus, a driver
generating a control signal with a minimum transition
time of 1ns must be connected to the converter pin
through a trace shorter than 2.5 inches. This problem
becomes particularly difficult when shared control lines
are used and multiple reflections may occur. The solution
is to carefully terminate all transmission lines close to
their characteristic impedance.
Parallel termination near the LTC2439-1 pin will eliminate
this problem but will increase the driver power dissipation.
A series resistor between 27
and 56 placed near the
driver or near the LTC2439-1 pin will also eliminate this
problem without additional power dissipation. The actual
resistor value depends upon the trace impedance and
connection topology.
An alternate solution is to reduce the edge rate of the
control signals. It should be noted that using very slow
edges will increase the converter power supply current
during the transition time. The differential input and refer-
ence architecture reduce substantially the converter’s
sensitivity to ground currents.
Particular attention must be given to the connection of the
FO signal when the LTC2439-1 is used with an external
conversion clock. This clock is active during the conver-
sion time and the normal mode rejection provided by the
internal digital filter is not very high at this frequency. A
normal mode signal of this frequency at the converter
reference terminals may result into DC gain and INL
errors. A normal mode signal of this frequency at the
converter input terminals may result into a DC offset error.
Such perturbations may occur due to asymmetric capaci-
tive coupling between the FO signal trace and the converter
input and/or reference connection traces. An immediate
solution is to maintain maximum possible separation
between the FO signal trace and the input/reference sig-
nals. When the FO signal is parallel terminated near the
converter, substantial AC current is flowing in the loop
formed by the FO connection trace, the termination and the
ground return path. Thus, perturbation signals may be
inductively coupled into the converter input and/or refer-
ence. In this situation, the user must reduce to a minimum
the loop area for the FO signal as well as the loop area for
the differential input and reference connections.
Driving the Input and Reference
The input and reference pins of the LTC2439-1 converter
are directly connected to a network of sampling capaci-
tors. Depending upon the relation between the differential
input voltage and the differential reference voltage, these
capacitors are switching between these four pins transfer-
ring small amounts of charge in the process. A simplified
equivalent circuit is shown in Figure 12.
For a simple approximation, the source impedance RS
driving an analog input pin (IN+, IN–, REF+ or REF–) can be
considered to form, together with RSW and CEQ (see
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD5535EBZ | BOARD EVALUATION FOR AD5535 |
| SDR0403-390KL | INDUCTOR POWER 39UH 0.59A 0403 |
| EBA22DRMD | CONN EDGECARD 44POS .125 SQ WW |
| EVAL-AD5757SDZ | BOARD EVAL FOR AD5757 |
| EVAL-AD5760SDZ | BOARD EVAL FOR AD5760SDZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC798B | 功能描述:BOARD DELTA SIGMA ADC LTC2480 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC-7G3EWA | 制造商:Kingbright Corporation 功能描述:Red/Green 10-seg LED lightbar, DC-7G3EWA |
| DC7G3HWA | 功能描述:LED條和陣列 7GR 3RED BARGRAFT 10 SEGMENT RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| DC-7G3HWA | 制造商:Kingbright Corporation 功能描述: |
| DC7K67J/4LR61 | 制造商:Duracell 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。