27 FN6785.0 July 29, 2010 Graceful Overcurrent and Short Circuit Hard faults from overcurrent or short circuit conditions sh" />
參數資料
型號： D2-45157-QR-T
廠商： Intersil
文件頁數： 20/31頁
文件大?。?/td> 0K
描述： IC DGTL AMP PWM CTRLR 68QFN
標準包裝： 3,000
系列： D2Audio™
類型： D 類
輸出類型： 2 通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 30W x 2 @ 8 歐姆
電源電壓： 9 V ~ 26 V
安裝類型： 表面貼裝
供應商設備封裝： 68-QFN 裸露焊盤（10x10）
封裝/外殼： 68-VFQFN 裸露焊盤
包裝： 帶卷 (TR)
D2-45057, D2-45157
27
FN6785.0
July 29, 2010
Graceful Overcurrent and Short Circuit
Hard faults from overcurrent or short circuit conditions
shut down the outputs. High-threshold over-temperature
also causes a shut down. For lower-threshold event
detections, graceful protection is provided for each
output. Specific operation depends on type and severity
of the detected event, but action taken is to reduce
conditions that would contribute to the event, without
the severity of a complete shut-down as in a high-limit
fault condition.
Overcurrent monitoring status is presented to the
PROTECT0-2 inputs, from per-output detector status that
drives the nERROR0-3 outputs. Overcurrent detection
algorithms in firmware monitor these peak level
detections, and upon detection of an overload condition,
automatically reduce PWM gain. This Automatic Gain
Control (AGC) action aids to prevent clipping of audio
output, as well as avoiding related excessive-level
conditions. The AGC algorithm operation functions
through a stepped-changing of PWM gain reduction,
corresponding to characteristics and time-event
detection of overloads. At the lower (non shut-down)
high-temperature threshold, the AGC function also acts to
attenuate the outputs to attempt to reduce temperature.
Output level gain and level change effects from this AGC
function are similar to operation from a compressor.
However, unlike a compressor where characteristics are
determined by input levels, the PWM AGC operation is
controlled through detection of near-overload output
levels or from high temperature detection.
Power Supply Voltage Monitoring
Undervoltage sensors and brownout detectors monitor all
supply voltages to the device. The logic and built-in
protection of this voltage monitoring prevents operation
until all supply voltages are within their specified limits.
Also, if any of these monitored voltages drop below their
threshold, the device shuts down its outputs and asserts
all four of the nERROR outputs.
Audio Processing
The audio processing, signal flow, and system definition
is defined by the D2-45057, D2-45157 device internal
ROM firmware, and executed by the DSP. This firmware
defines the audio flow architecture, which includes the
audio processing blocks. Each of these blocks are
programmable, allowing for adjustment of their
audio-controlling parameters. The signal flow and audio
processing blocks are shown in Figure 17. This
architecture includes audio processing functions of:
Input Selection
Mixers
Input Compressors and Output Limiters
Tone Controls
5-Band and 3-Band Parametric Equalizers
Router
High/Low-Pass Crossover Filters
Volume and Output Level Controls
Loudness Contour
Enhancement audio processing is also used. Depending
on which device, (D2-45057 or D2-45157) either the
D2Audio SoundSuite or SRS WOW/HD algorithms
are included.
Audio Processing Signal Flow Blocks
INPUT SELECTION
The Input Select register specifies the audio inputs that
are assigned to the audio processing input path. Either
the I2S or S/PDIF Digital inputs are available.
MIXERS
An input mixer provides a two-input, two-output mixing
and routing path. Either input can be mixed at adjustable
gain into either or both of the two outputs. Default
setting is 0 dB through each channel, with full cut-off for
non-through channels. Attenuation is continuously
variable with the programmable parameters.
A stereo mixer provides a path from the two input
channels. This typically is used to provide a mix of both
stereo input channels for crossover processing and
becoming the source for the subwoofer channel. Gains
for both input channels are adjustable to feed the single
stereo mixer output.
TONE CONTROLS
A tone control block is included in both of the two input
channels. Each of the filters (bass or treble) is
implemented with a first-order (6dB/octave) roll-off,
using programmable corner frequency and a boost or
attenuating gain. The signal flow processing
automatically provides a smooth transition between tone
control changes.
相關PDF資料
PDF描述
D38999/26WB5BN CONN HSG PLUG 5POS STRGHT SCKT
D2-45057-QR-T IC DGTL AMP PWM CTRLR 68QFN
D38999/26WD5BN CONN HSG PLUG 5POS STRGHT SCKT
D38999/24WD97SNLC CONN HSG RCPT 12POS JAM NUT SCKT
VI-B6P-IV-F2 CONVERTER MOD DC/DC 13.8V 150W
相關代理商/技術參數
參數描述
D245-5 制造商:KLEIN TOOLS 功能描述:Plier, Diagonal-Cutting; Tapered; 5-1/16 in.; 11/16 in.; 9/16 in.; 3/8 in.; Red 制造商:Klein Tools Inc 功能描述:TOOLS PLIERS 制造商:KLEIN TOOLS 功能描述:TOOLS, PLIERS; Plier Style:Diagonal Cutting; Jaw Length:18mm; Overall Length:129mm; Features:Tapered nose gets in confined areas; ideal for close-tip cutting; Handle Color:Red ;RoHS Compliant: NA 制造商:Klein Tools Inc 功能描述:Standard Diagonal Cutting Pliers
D245-5C 制造商:Klein Tools Inc 功能描述:
D246 制造商:PETERMANN 制造商全稱:PETERMANN 功能描述:HIGH RELIABILITY FOR LOW COST
D24-6 制造商:RICHARD MANNO 功能描述:
D24683-000 制造商:TE Connectivity 功能描述:Heat Shrink Molded Boot 制造商:TE Connectivity 功能描述:222K121-25-CS-2101-0 - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*