- 您現在的位置：買賣IC網 > PDF目錄2067 > D2-24044-MR (Intersil)IC DGTL AMP AUDIO PWR D 38HTSSOP PDF資料下載
參數資料
| 型號： | D2-24044-MR |
| 廠商： | Intersil |
| 文件頁數： | 3/20頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL AMP AUDIO PWR D 38HTSSOP |
| 標準包裝： | 50 |
| 系列： | D2Audio™ |
| 類型： | D 類 |
| 輸出類型： | 2-通道（立體聲）或 4 通道（四路） |
| 在某負載時最大輸出功率 x 通道數量： | 30W x 2 @ 8 歐姆 |
| 電源電壓： | 9 V ~ 26 V |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 38-HTSSOP |
| 封裝/外殼： | 38-TFSOP （0.173"，4.40mm 寬）裸露焊盤 |
| 包裝： | 管件 |
11
FN7678.0
September 3, 2010
Input and Control Functions
PWM Inputs
Eight PWM input pins provide the PWM inputs to the
amplifier’s output stages. The PWM input pins are
electrically single-ended, referenced to the PWMVDD and
PWMGND supplies.
PWM drive to the output stages is provided differentially
on-chip, with the PWM input channels mapped to each of
the high-side output FETs and the low-side output FETs
that implement the individual power stages. Routing and
assignment of the PWM input pins to the output FETS is
defined by the configuration mode. Figures 11, 12, 13,
and 14 show the mapping of these input pins to the
outputs for each of the four configuration modes.
All eight input pins however are not always used in each
of the configuration modes. For example, in mode “00”,
providing 3-level drive of two channels of full bridge
outputs, or in mode “11” providing four independent
half-bridge outputs, one PWM input is dedicated to each
of the FETs. But in mode “01” that implements two
2-quadrant full-bridge outputs, only four PWM inputs are
used, and the logical high/low states are routed to the
FETs as needed.
nPDN Input Pin
The nPDN pin is a control input that is used to set the
inactive (powered down) state, and also mute the
outputs. It operates by turning off drive and internal
sources to the PWM outputs, as well as turning off the
PWM drive to those outputs.
When an overcurrent condition is detected on an output,
causing its overcurrent protection to latch and turn off
that output, asserting the nPDN input resets the device,
and clears this overcurrent state.
The nPDN pin is active low, and inactive when at logic
high level.
nERRORA-D Output Pins
Each of the four outputs includes an overload and
overcurrent monitor. An overcurrent or overload
condition asserts the nERROR output for that channel.
These outputs are active low, open drain. Depending on
the output mode configuration and need to monitor more
than one output, these nERROR pins can be wire-or
connected together.
nOVRT Output Pin
The nOVRT pin is an output that provides warning of a
high temperature condition. It is an open drain, active
low output. This pin provides only indication of high
temperature.
IREF Pin
The IREF pin is used to control the overcurrent
monitoring threshold. A 100kΩ resistor connects from
this pin to ground.
OCFG0, OCFG1 Input Pins
These two pins are used to define the configuration of the
four output stages. They are connected to logic high
(PWMVDD) or logic ground (PWMGND) to set their level.
Refer to “Output Mode Configurations” on page 14 for
additional reference and definition.
Protection
The D2-24044 device includes monitors for protection of
the system as well as the device itself. Certain levels of
protection are managed on-chip, as shown in Figure 10.
Other protection is integrated at the system level
through the system controller, and involves system
design decisions based on:
A short circuit, over-temperature, or undervoltage
event will shut down the outputs.
Other operation depends on the PWM/system
controller to properly manage full system protection
operation.
Power supply sensors shut down the device if supply
voltages drop below their design thresholds.
Overload and overcurrent monitors provide dual
threshold status of high current conditions, providing
both indication, and device shutdown if needed.
Chip temperature monitoring provides dual threshold
status of high temperature conditions, providing
both indication, and device shutdown if needed.
Short-Circuit and Overcurrent Sensing
Each PWM output FET includes a dual-threshold
overcurrent sensor. Multiple functions occur depending
on detection of overcurrent conditions:
The lower threshold is used to monitor fault
conditions after the output stage filter inductor, such
as shorts or overloads on the loudspeaker outputs.
The higher threshold monitors fault conditions of the
PWM output pin.
The nERROR output asserts for the channel detecting
the fault.
For the lower level threshold, nERROR remains
asserted only through the duration of the
overcurrent event.
For the higher level threshold, the output is shut
down, and its nERROR output is asserted, and these
remain latched until the controller acknowledges the
fault event by turning off the channel’s PWM drive.
(When the output is shutdown, its PWM output pin
floats.)
D2-24044
相關PDF資料 |
PDF描述 |
|---|---|
| D2-45157-QR | IC DGTL AMP PWM CTRLR 68QFN |
| DS1080CLU+ | IC CRYSTAL MULTIPLIER SS 8-MSOP |
| DS1080LU+A00 | IC CRYSTAL MULT SS 8-USOP |
| DS1085LZ-12+ | IC ECONOSCILLATOR SYNTH 8-SOIC |
| DS1085Z-25+ | IC ECONOSCILLATOR SYNTH 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| D2-24044-MR-T | 功能描述:音頻放大器 LW-PWR CLASS-AMPLIFI 3 8LD HTSSOP 4 4X9 7 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| D224E | 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Low Cost, 2W SIP Single & Dual Output DC/DC Converters |
| D224ED | 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Very Low Cost, 2W SIP Dual Isolated Output DC/DC Converters |
| D224EI | 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Low Cost, 2W SIP High Isolation DC/DC Converters |
| D224ERW | 制造商:MPD 制造商全稱:MicroPower Direct, LLC 功能描述:Low Cost, Miniature 2W SIP, Wide Input DC/DC Con vert ers |
發布緊急采購，3分鐘左右您將得到回復。