參數資料
型號： CY7C65640-LFXC
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： 總線控制器
英文描述： TetraHub High-speed USB Hub Controller
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, QCC56
封裝： 8 X 8 MM, LEAD FREE, QFN-56
文件頁數： 7/27頁
文件大?。?/td> 675K
代理商： CY7C65640-LFXC
CY7C65640
Document #: 38-08019 Rev. *E
Page 7 of 27
2.3
The Hub Control Block does the following protocol handling at a higher level:
Coordinate enumeration by responding to SETUP packets
Fill and empty the FIFOs
Suspend/Resume coordination
Verify and select DATA toggle values
Port power control and over-current detection.
The Hub Controller provides status and control and permits host access to the hub.
Hub Controller
2.4
The Hub Repeater manages the connectivity between upstream and downstream facing ports that are operating at the same
speed. It supports full-/low-speed connectivity and high-speed connectivity. Per the USB 2.0 specification, the Hub Repeater
provides the following functions:
Sets up and tears down connectivity on packet boundaries
Ensures orderly entry into and out of the Suspend state, including proper handling of remote wakeups.
Hub Repeater
2.5
The TT basically translates data from one speed to another. A TT takes high-speed split transactions and translates them to
full-/low-speed transactions when the hub is operating at high speed (the upstream port is connected to a high-speed host
controller) and has full-/low-speed devices attached. The operating speed of a device attached on a downstream facing port
determines whether the Routing Logic connects a port to the Transaction Translator or Hub Repeater section. If a low-/full-speed
device is connected to the hub operating at high speed, the data transfer route includes the transaction translator. If a high-speed
device is connected to this high-speed hub the route only includes the repeater and no transaction translator since the device
and the hub are in conformation with respect to their data transfer speed. When the hub is operating at full speed (the upstream
port is connected to a full-speed host controller), a high-speed peripheral will not operate at its full capability. These devices will
only work at 1.1 speed. Full- and low-speed devices connected to this hub will operate at their 1.1 speed.
Transaction Translator
3.0
Applications
Standalone Hubs
Motherboard Hubs
Monitor Hub applications
External Personal Storage Drives
Port Replicators
Portable Drive
Docking Stations
4.0
Functional Overview
The Cypress TetraHub USB 2.0 Hub is a high-performance, low-system-cost solution for USB. The TetraHub USB 2.0 Hub
integrates 1.5k upstream pull-up resistors for full-speed operation and all downstream 15k pull-down resistors as well as series
termination resistors on all upstream and downstream D+ and D– pins. This results in optimization of system costs by providing
built-in support for the USB 2.0 specification.
4.1
On power-up, the TetraHub will read an external SPI EEPROM for configuration information. At the most basic level, this EEPROM
will have the Vendor ID (VID), Product ID (PID), and Device ID (DID) for the customer's application. For more specialized
applications, other configuration options can be specified. See section 8.0 for more details.
After reading the EEPROM, if BUSPOWER (connected to up-stream VBus) is HIGH, TetraHub will enable the pull-up resistor on
the D+ to indicate that it is connected to the upstream hub, after which a USB Bus Reset is expected. During this reset, TetraHub
will initiate a chirp to indicate that it is a high-speed peripheral. In a USB 2.0 system, the upstream hub will respond with a chirp
sequence, and TetraHub will be in a high-speed mode, with the upstream D+ pull-up resistor turned off. In USB 1.x systems, no
such chirp sequence from the upstream hub will be seen, and TetraHub will operate as a normal 1.x hub (operating at full speed).
System Initialization
4.2
After a USB Bus Reset, TetraHub is in an unaddressed, unconfigured state (configuration value set to 0). During the enumeration
process, the host will set the hub's address and configuration by sending a SetCongfiguration request. Changing the hub address
will restore it to an unconfigured state.
Enumeration
相關PDF資料
PDF描述
CY7C65640 TetraHub High-speed USB Hub Controller
CY7C65640-LFC TetraHub High-speed USB Hub Controller
CY4602 TetraHub High-speed USB Hub Controller
CY7C65640A TetraHub High-Speed USB Hub Controller(TetraHub高速USB Hub控制器)
CY7C67200 EZ-OTG Programmable USB On-The-Go Host/Peripheral Controller(EZ-OTG可編程USB On-The-Go主機/外圍設備控制器)
相關代理商/技術參數
參數描述
CY7C65642-28LTXC 功能描述:USB 接口集成電路 TetraHub Ctrl USB2.0 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C65642-28LTXCT 制造商:Cypress Semiconductor 功能描述:USB HIGH SPEED HUBS - Tape and Reel 制造商:Cypress Semiconductor 功能描述:INTERFACE CONTROLLER
CY7C65642-48AXC 功能描述:USB 接口集成電路 CY7C65642-48AXC RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C65642-48AXCT 功能描述:USB 接口集成電路 CY7C65642-48AXCT RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C66013C-PVXC 功能描述:8位微控制器 -MCU USB Hubs RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*