參數資料
型號： CY7C65640-LFXC
廠商： CYPRESS SEMICONDUCTOR CORP
元件分類： 總線控制器
英文描述： TetraHub High-speed USB Hub Controller
中文描述： UNIVERSAL SERIAL BUS CONTROLLER, QCC56
封裝： 8 X 8 MM, LEAD FREE, QFN-56
文件頁數： 17/27頁
文件大小： 675K
代理商： CY7C65640-LFXC
CY7C65640
Document #: 38-08019 Rev. *E
Page 17 of 27
Byte 5: DID (LSB)
Least Significant Byte of Device ID
Byte 6: DID (MSB)]
Most Significant Byte of Device ID
Byte 7: EnableOvercurrentTimer[3:0], DisabledOvercurrentTimer[3:0]
Count time in ms for filtering overcurrent detection. Bits 7–4 are for an enabled port, and bits 3–0 are for a disabled port. Both
range from 0 ms to 15 ms. See section 4.8. Default: 8 ms = 0x88.
Byte 8: ActivePorts[3:0], RemovablePorts[3:0]
Bits 7–4 are the ActivePorts[3:0] bits that indicates if the corresponding port is usable. For example, a two-port hub that uses
ports 1 and 4 would set this field to 0x09. The total number of ports reported in the Hub Descriptor: bNbrPorts field is calculated
from this. Bits 3–0 are the RemovablePorts[3:0] bits that indicates whether the corresponding port is removable (set to HIGH).
This bit’s values are recorded appropriately in the HubDescriptor:DeviceRemovable field. Default: 0xFF.
Byte 9: MaximumPower
This value is reported in the ConfigurationDescriptor:bMaxPower field and is the current in 2-mA intervals that is required from
the upstream hub. Default: 0x32 = 100 mA
Byte 10: HubControllerPower
This value is reported in the HubDescriptor:bHubContrCurrent field and is the current in milliamperes required by the hub
controller. Default: 0x64 = 100 mA.
Byte 11: PowerOnTimer
This value is reported in the HubDescriptor:bPwrOn2PwrGood field and is the time in 2-ms intervals from the SetPortPower
command until the power on the corresponding downstream port is good. Default: 0x32 = 100 ms.
Byte 12: IllegalHubDescriptor, Unused, FullspeedOnly, NoPortIndicators, Reserved, GangPowered, SingleTTOnly,
NoEOPatEOF1
Bit 7: IllegalHubDescriptor: For GetHubDescriptor request, some USB hosts use a DescriptorTypeof 0x00 instead of
HUB_DESCRIPTOR, 0x29. According to the USB 2.0 standard, a hub must treat this as a Request Error, and STALL the
transaction accordingly (USB 2.0, 11.24.2.5). For systems that do not accept this, the IllegalHubDescriptor configuration bit
may be set to allow TetraHub to accept a DescriptorType of 0x00 for this command. Default is 0, recommended setting is 1.
Bit 6: Unused: This bit is an unused, don’t care bit and can be set to anything.
Bit 5: Fullspeed: Only configures the hub to be a full-speed only device. Default set to 0.
Bit 4: NoPortIndicators: Turns off the port indicators and does not report them as present in the HubDescriptor, wHubCharac-
teristics b7 field. Default set to 0.
Bit 3: Reserved: This bit is reserved and should not be set to 1. Must be set to 0.
Bit 2: GangPowered: Indicates whether the port power switching is ganged (set to 1) or per-port (set to 0). This is reported in
the HubDescriptor, wHubCharacteristics field, b4, b3, b1, and b0. Default set to 0.
Bit 1: SingleTTOnly: Indicates that the hub should only support single Transaction Translator mode. This changes various
descriptor values. Default set to 0.
Bit 0: NoEOPatEOF1 turns off the EOP generation at EOF1 in full-speed mode. Note that several USB 1.1 hosts can not
handle EOPatEOF1 properly. Cypress recommends that this option be turned off for general-purpose hubs. Default is 0,
recommended setting is 1.
相關PDF資料
PDF描述
CY7C65640 TetraHub High-speed USB Hub Controller
CY7C65640-LFC TetraHub High-speed USB Hub Controller
CY4602 TetraHub High-speed USB Hub Controller
CY7C65640A TetraHub High-Speed USB Hub Controller(TetraHub高速USB Hub控制器)
CY7C67200 EZ-OTG Programmable USB On-The-Go Host/Peripheral Controller(EZ-OTG可編程USB On-The-Go主機/外圍設備控制器)
相關代理商/技術參數
參數描述
CY7C65642-28LTXC 功能描述:USB 接口集成電路 TetraHub Ctrl USB2.0 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C65642-28LTXCT 制造商:Cypress Semiconductor 功能描述:USB HIGH SPEED HUBS - Tape and Reel 制造商:Cypress Semiconductor 功能描述:INTERFACE CONTROLLER
CY7C65642-48AXC 功能描述:USB 接口集成電路 CY7C65642-48AXC RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C65642-48AXCT 功能描述:USB 接口集成電路 CY7C65642-48AXCT RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
CY7C66013C-PVXC 功能描述:8位微控制器 -MCU USB Hubs RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*