參數資料
型號: CXD2589Q
廠商: Sony Corporation
元件分類: 數字信號處理
英文描述: CD Digital Signal Processor
中文描述: CD數字信號處理器
文件頁數: 57/61頁
文件大?。?/td> 794K
代理商: CXD2589Q
– 57 –
CXD2589Q
Normal
DBB MID
DBB MAX
10.00
–4.00
6.00
4.00
2.00
0.00
–2.00
8.00
–6.00
–8.00
–10.00
–12.00
–14.00
10
30
100
300
1k
3k
10k
30k
Digital Bass Boost Frequency Response [Hz]
[
Graph 5-2.
LRCK Synchronization
Synchronization is performed at the first falling edge of the LRCK input during reset.
After that, synchronization is lost when the LRCK input frequency changes and resynchronization must be
performed.
The LRCK input frequency changes when the master clock of the LSI is switched and the playback speed
changes such as the following cases.
When the XTSL pin switches between high and low
When the DSPB command of $9X setting changes
When the MCSL command of $9X setting changes
LRCK switching may also be performed if there are other ICs between the CD-DSP block and the DAC
block. Resynchronization must be performed in this case as well.
For resynchronization, set the LRWO command of $AX to 1, wait for one LRCK cycle or more, and then set
LRWO to 0.
When setting LRWO, set OPSL2 to 1. (See the $AX commands.)
SYCOF
When LRCK, PCMD and BCK are connected directly with LRCKI, PCMDI and BCKI, respectively, playback
can be performed easily in CAV-W mode by setting SYCOF of address 9 to 1.
Normally, the memory proof, etc., is used for playback in CAV-W mode.
In CAV-W mode, the LRCK output conforms not to the crystal but to the VCO. Therefore, synchronization is
frequently lost.
Setting SYCOF of address 9 to 1 ignores that the LRCKI input synchronization is lost, facilitating playback.
However, the playback is not perfect because pre-value hold or data skip occurs due to the wow flutter in the
LRCKI input.
Set SYCOF to 0 except when connecting LRCK, PCMD and BCK directly with LRCKI, PCMDI and BCKI,
respectively, and performing playback in CAV-W mode.
Set SYCOF to 0 in advance when LRCK resynchronization is applied with LRWO=1.
Digital Bass Boost
Bass boost without external parts is possible using the built-in digital filter. The boost strength has two levels:
Mid. and Max. BSBST and BBSL of address A are used for the setting.
See Graph 5-2 for the digital bass boost frequency response.
相關PDF資料
PDF描述
CXD2598Q CD Digital Signal Processor with Built-in Digital Servo and DAC(數字式CD信號處理器(內置數字式伺服系統和D/A轉換器))
CXD2598 CD Digital Signal Processor with Built-in Digital Servo and DAC
CXD2719Q Single-Chip Dolby Pro Logic Surround Decoder(單片杜比環繞邏輯譯碼器)
CXD2720Q Single-Chip Digital Signal Processor for Karaoke(卡拉OK單片數字信號處理器)
CXD2721Q-1 Single-Chip Digital Signal Processor for Karaoke
相關代理商/技術參數
參數描述
CXD2597Q 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD Digital Signal Processor with Built-in Digital Servo and DAC
CXD2598 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD Digital Signal Processor with Built-in Digital Servo and DAC
CXD2598Q 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD Digital Signal Processor with Built-in Digital Servo and DAC
CXD2719Q 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Single-Chip Dolby Pro Logic Surround Decoder
CXD2720Q 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Single-Chip Digital Signal Processor for Karaoke