- 您現在的位置：買賣IC網 > PDF目錄378985 > CXD2589Q (Sony Corporation) CD Digital Signal Processor PDF資料下載
參數資料
| 型號： | CXD2589Q |
| 廠商： | Sony Corporation |
| 元件分類： | 數字信號處理 |
| 英文描述： | CD Digital Signal Processor |
| 中文描述： | CD數字信號處理器 |
| 文件頁數： | 47/61頁 |
| 文件大?。?/td> | 794K |
| 代理商： | CXD2589Q |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁當前第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
– 47 –
CXD2589Q
Fig. 4-3-(b). Auto Focus Timing Chart
(b) Track Jump
1, 10, and 2N-track jumps are performed respectively. Always use this when the focus, tracking, and sled
servos are on. Note that tracking gain-up and braking-on should be sent beforehand because they are not
involved in this sequence.
1-track jump
When $48 ($49 for REV) is received from the CPU, a FWD (REV) 1-track jump is performed in accordance
with Fig. 4-4. Set blind A and brake B with register 5.
10-track jump
When $4A ($4B for REV) is received from the CPU, a FWD (REV) 10-track jump is performed in
accordance with Fig. 4-5. The principal difference from the 1-track jump is to kick the sled. In addition, after
kicking the actuator, when 5 tracks have been counted through CNIN, the brake is applied to the actuator.
Then, when the actuator speed is found to have slowed up enough (determined by the CNIN cycle
becoming longer than the overflow C set with register 5), the tracking and sled servos are turned on.
2N-track jump
When $4C ($4D for REV) is received from the CPU, a FWD (REV) 2N-track jump is performed in
accordance with Fig. 4-6. The track jump count N is set with register 7. Although N can be set to 216 tracks,
note that the setting is actually limited by the actuator. CNIN is used for counting the number of jumps.
Although the 2N-track jump basically follows the same sequence as the 10-track jump, the one difference is
that after the tracking servo is turned on, the sled continues to move only for "D", set with register 6.
N-track move
When $4E ($4F for REV) is received from the CPU, a FWD (REV) N-track move is performed in
accordance with Fig. 4-7. N can be set to 216 tracks. CNIN is used for counting the number of jumps. This
N-track move is executed only by moving the sled, and is therefore suited for moving across several
thousand to several ten-thousand tracks.
XLT
FOK
SEIN (FZC)
BUSY
Command for SSP
$47latch
$03
Blind E
$08
相關PDF資料 |
PDF描述 |
|---|---|
| CXD2598Q | CD Digital Signal Processor with Built-in Digital Servo and DAC(數字式CD信號處理器（內置數字式伺服系統和D/A轉換器）) |
| CXD2598 | CD Digital Signal Processor with Built-in Digital Servo and DAC |
| CXD2719Q | Single-Chip Dolby Pro Logic Surround Decoder(單片杜比環繞邏輯譯碼器) |
| CXD2720Q | Single-Chip Digital Signal Processor for Karaoke(卡拉OK單片數字信號處理器) |
| CXD2721Q-1 | Single-Chip Digital Signal Processor for Karaoke |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CXD2597Q | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD Digital Signal Processor with Built-in Digital Servo and DAC |
| CXD2598 | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD Digital Signal Processor with Built-in Digital Servo and DAC |
| CXD2598Q | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:CD Digital Signal Processor with Built-in Digital Servo and DAC |
| CXD2719Q | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Single-Chip Dolby Pro Logic Surround Decoder |
| CXD2720Q | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Single-Chip Digital Signal Processor for Karaoke |
發布緊急采購，3分鐘左右您將得到回復。