- 您現在的位置：買賣IC網 > PDF目錄369674 > CT2555-FP (Aeroflex Inc.) CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 PDF資料下載
參數資料
| 型號： | CT2555-FP |
| 廠商： | Aeroflex Inc. |
| 英文描述： | CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| 中文描述： | CT2553 / 2554 /二千五百五十六分之二千五百五十五高級集成復用器（AIM）的混合的MIL - STD - 1553的 |
| 文件頁數： | 19/36頁 |
| 文件大?。?/td> | 352K |
| 代理商： | CT2555-FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Aeroflex Circuit Technology
19
SCDCT2553 REV B 8/6/99 Plainview NY (516) 694-6700
MT OPERATION
Initiate a Reset in order to initialize the CT2553.
Configure the CT2553 as a Bus Monitor (MT) by
setting the appropriate Configuration Register
Bits. See Figure 24 for MT initialization Steps.
MT MEMORY CONFIGURATION
. The user
configures the memory by writing the start
address for 1553 data storage into the Stack
Pointer
location.
The
automatically wrap around once the RAM has
been filled (i.e., location FFF(H) is followed by
location 0000). An example of a typical MT
Memory Map 4 given in Table 5.
Table 5 – Typical MT Memory Map
HEX ADDRESS
0000
First Received 1553 Word
0001
First Identification Word
0002
Second Received 1553 Word
0003
Second Identification Word
0004
0005
0006
0100
Stack Pointer (Fixed location)
FFFF
Monitor
Stack
will
MT START SEQUENCE
. After setting the
CONTROLLER START bit in the Start/Reset
Register, the CT2553 takes the following actions:
1. Reads the start address for 1553 data storage
from the Stack Pointer location. The Stack
Pointer location(s) will be overwritten with 1553
data once the MT mode has begun and 1553
data is written into locations 0100(H) and
0101(H)].
2. Stores the received 1553 word into memory.
3. Increments the Stack Pointer by 1.
4.Generates an Identification Word and stores
this value into memory.
5.Repeats steps 2-4 until a Reset condition
occurs.
MT IDENTIFICATION WORD
. The Identification
word provides the CPU with information pertaining
to the received 1553 word. Its format is shown in
Figure 25, This information allows the user to
analyze the 1553 data.
THIS-RT
: Each command appearing on either
1553
Bus
is
decoded
Manchester/protocol
errors.
receives a valid command word containing a
Command Sync and a RTU address equivalent to
the RTAD0-RTAD4 inputs (pins 10, 9, 50, 49, and
11, respectively), THIS-RT (pin 55) will be pulsed
low. This signal can be used to identify specific
1553 commands or for switching to RTU mode
upon receipt of a command to this address.
and
If
tested
the
for
CT2553
FUNCTION
MSB
15
LSB
8 7 6
5 4 3 2 1 0
1
GAP TIME
WORD FLAG
THIS RT
BROADCAST
ERROR
COMMAND SYNC
1553 CHANNEL A/B
CONTIGUOUS DATA
MODE CODE
BIT NAME
DEFINITION
GAP TIME
Indicates the time between receipt of the
previous and current words.Time is
indicated in 0.5μs increments for a
maximum of 128 μs and goes to FF over
128μs. (See Word Gap bit.)
Always logic 1.
Logic 0 indicates RT address field of the
associated command or Status Word
matches the RT address field of the
CT2553.
Logic 0 indicates the RTU address field of
the command or Status Word
corresponds to address 31 (decimal).
Logic 1 indicates Manchester, Parity,
Sync and/or low bit counter.
Logic 1 indicates 1553 Command or
Status Word sync field. (Logic 0 indicates
a Data Word sync field in received word.)
Indicates word received on 1553 Bus A
(1) or Bus B (0).
Logic 1 indicates the word was received
within 2μs of the previous word. If logic 0,
bits 8-15 contain the measured gap
between the words.
When logic 1, the data transferred is a
mode code command.
WORD FLAG
THIS RT
BROADCAST
ERROR
COMMAND SYNC
1553 CHANNEL
A/B
CONTIGUOUS
DATA
MODE CODE
Figure 25 – MT Identification Word
START
ISSUE RESET COMMAND
CLEAR RAM
ISSUE START COMMAND
INITIALIZE STACK POINTER
SET CONFIGURATION
REGISTER TO MT MODE
Figure 24 – MT Initialization
相關PDF資料 |
PDF描述 |
|---|---|
| CT2553 | CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| CT2554 | CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| CT2555 | CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| CT2553-FP | CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| CT2556 | CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CT2556 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| CT2556-FP | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2553 / 2554 / 2555 / 2556 Advanced Integrated MUX (AIM) Hybrid FOR MIL-STD-1553 |
| CT2561 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2561 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2561-FP | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2561 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
| CT2565 | 制造商:AEROFLEX 制造商全稱:AEROFLEX 功能描述:CT2565 Bus Controller, Remote Terminal and BUS Monitor FOR MIL-STD-1553B |
發布緊急采購，3分鐘左右您將得到回復。