- 您現在的位置：買賣IC網 > PDF目錄169782 > COP8SGR728Q3XXX (NATIONAL SEMICONDUCTOR CORP) 8-BIT, UVPROM, MICROCONTROLLER, CDIP28 PDF資料下載
參數資料
| 型號： | COP8SGR728Q3XXX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, UVPROM, MICROCONTROLLER, CDIP28 |
| 封裝： | WINDOWED, DIP-28 |
| 文件頁數： | 10/62頁 |
| 文件大?。?/td> | 840K |
| 代理商： | COP8SGR728Q3XXX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
5.0 Functional Description (Continued)
output will continue until 16 t
C–32 tC clock cycles following
the clock frequency reaching the minimum specified value,
at which time the G1 output will go high.
5.9.1 External Reset
The RESET input when pulled low initializes the device. The
RESET pin must be held low for a minimum of one instruc-
tion cycle to guarantee a valid reset. During Power-Up ini-
tialization, the user must ensure that the RESET pin is held
low until the device is within the specified V
CC voltage. An
R/C circuit on the RESET pin with a delay 5 times (5x)
greater than the power supply rise time or 15 s whichever is
greater, is recommended. Reset should also be wide enough
to ensure crystal start-up upon Power-Up.
RESET may also be used to cause an exit from the HALT
mode.
A recommended reset circuit for this device is shown in
Figure 10.
5.9.2 On-Chip Power-On Reset
The on-chip reset circuit is selected by a bit in the ECON
register. When enabled, the device generates an internal
reset as V
CC rises to a voltage level above 2.0V. The on-chip
reset circuitry is able to detect both fast and slow rise times
on V
CC (VCC rise time between 10 ns and 50 ms).To guar-
antee an on-chip power-on-reset, V
CCmust start at a voltage
less than the start voltage specified in the DC characteris-
tics. Also, if V
CC be lowered to the start voltage before
powering back up to the operating range. If this is not pos-
sible, it is recommended that external reset be used.
Under no circumstances should the RESET pin be allowed
to float. If the on-chip Power-On Reset feature is being used,
RESET pin should be connected directly, or through a
pull-up resistor, to V
CC. The output of the power-on reset
detector will always preset the Idle timer to 0FFF(4096 t
C).
At this time, the internal reset will be generated.
If the Power-On Reset feature is enabled, the internal reset
will not be turned off until the Idle timer underflows. The
internal reset will perform the same functions as external
reset. The user is responsible for ensuring that V
CC is at the
minimum level for the operating frequency within the 4096
t
C. After the underflow, the logic is designed such that no
additional internal resets occur as long as V
CC remains
above 2.0V.
The contents of data registers and RAM are unknown fol-
lowing the on-chip reset.
5.10 OSCILLATOR CIRCUITS
There are four clock oscillator options available: Crystal
Oscillator with or without on-chip bias resistor, R/C Oscillator
with on-chip resistor and capacitor, and External Oscillator.
The oscillator feature is selected by programming the ECON
register, which is summarized in
Table 1.
TABLE 1. Oscillator Option
ECON4
ECON3
Oscillator Option
0
External Oscillator
1
0
Crystal Oscillator without Bias Resistor
0
1
R/C Oscillator
1
Crystal Oscillator with Bias Resistor
DS101317-14
RC >5x power supply rise time or 15 s, whichever is greater.
FIGURE 10. Reset Circuit Using External Reset
DS101317-15
FIGURE 11. Reset Timing (Power-On Reset Enabled)
with V
CC Tied to RESET
DS101317-16
FIGURE 12. Reset Circuit Using Power-On Reset
COP8SG
Family
www.national.com
18
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SGE728N8XXX | 8-BIT, OTPROM, 15 MHz, MICROCONTROLLER, PDIP28 |
| COP8SGR728M8XXX | 8-BIT, OTPROM, 15 MHz, MICROCONTROLLER, PDSO28 |
| COP8SGR744J3XXX | 8-BIT, UVPROM, MICROCONTROLLER, CQCC44 |
| COP8SGE744V8XXX | 8-BIT, OTPROM, 15 MHz, MICROCONTROLLER, PQCC44 |
| COP8SGE744V7XXX | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SGR740N8 | 功能描述:IC MCU 8BIT CMOS OTP 40DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SG 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| COP8SGR740N8/NOPB | 制造商:Texas Instruments 功能描述: |
| COP8SGR744V8 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8SGR744V8 | 制造商:Texas Instruments 功能描述:8BIT MCU OTP 32K 8SGR744 PLCC44 |
| COP8SGR744V8/63 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。