- 您現在的位置：買賣IC網 > PDF目錄17026 > CDB5529 (Cirrus Logic Inc)EVAL BOARD FOR CS5529 PDF資料下載
參數資料
| 型號： | CDB5529 |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 7/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR CS5529 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 303 |
| 數據接口： | 串行 |
| 輸入范圍： | ±2.5 V |
| 在以下條件下的電源（標準）： | 2.6mW @ 2.5V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | CS5529 |
| 已供物品： | 板，線纜，磁盤 |
| 產品目錄頁面： | 755 (CN2011-ZH PDF) |
| 相關產品： | CS5529-ASZR-ND - IC ADC 16BIT W/6BIT LATCH 20SSOP 598-1110-5-ND - IC ADC 16BIT W/6BIT LATCH 20SSOP |
| 其它名稱： | 598-1015 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
CS5529
DS246F5
15
Serial Port Initialization
The serial port is initialized to the command mode
whenever a power-on reset is performed or when
the port initialization sequence is completed. The
port initialization sequence involves clocking fif-
teen (or more) SYNC1 command bytes (0xFF) fol-
lowed by one SYNC0 command byte (0xFE). This
sequence places the chip in the command mode
where it waits until a valid command is received.
This function does not reset the internal registers to
their default settings. It only resets the serial port to
the command mode.
System Initialization
When power to the CS5529 is applied, the chip is
held in a reset condition until the 32.768 kHz oscil-
lator has started and a counter-timer elapses. Due to
the high Q of the 32.768 kHz crystal, the oscillator
takes 400-600 ms to start. The counter-timer counts
1002 oscillator clock cycles to make sure the oscil-
lator is fully stable. During this time-out period the
serial port logic is reset and the RV (Reset Valid)
bit in the configuration register is set to indicate
that a valid reset occurred. After a reset, the on-chip
registers are initialized to the following states and
the converter is placed in the command mode
where it waits for a valid command.
Note:
A system reset can be initiated at any time by
writing a logic 1 to the RS (Reset System) bit
in the configuration register. After a reset, the
RV (Reset Valid) bit is set until the
configuration register is read. The user must
then write a logic 0 to the RS bit to take the
part out of the reset mode.
Configuration Register
The configuration register is a 24 bit register used
to modify the functions of the ADC. The following
sections detail the functions of the bits in the con-
figuration register.
Latch Output Pins
The D3-D0 pins of the converter mimic the D21-
D18 bits of the configuration register. D3-D0 can
be used to control multiplexers and other digital
logic functions outside the converter. The D0-D3
outputs are powered from VD+ and DGND. Their
output voltage will be VD+ for a logic 1 and
DGND for a logic 0. The A1-A0 pins of the con-
verter mimic the D23-D22 bits of the configuration
register and can be used to control analog switches.
These outputs are powered from VA+ and VA-,
hence, their output voltage will be either VA+ for a
logic 1 or VA- for a logic 0.
All outputs can sink or source at least 1 mA, but it
is recommended to limit drive currents to less than
20
A to reduce self-heating of the chip.
Power Consumption
The CS5529 accommodates four power consump-
tion modes: normal, low power, standby, and sleep.
The normal mode, the default mode, is entered after
a power-on-reset and typically consumes 2.5 mW.
The low power mode is an alternate mode that re-
duces the consumed power to 1.4 mW. It is entered
by setting bit D16 (the low power mode bit) in the
configuration register to logic 1. Since the convert-
er’s noise and linearity performance improves with
increased power consumption, slightly degraded
noise or linearity performance should be expected
in the low power mode.
The final two modes are the power save modes.
These modes power down most of the analog por-
tion of the chip and stop filter convolutions. The
power save modes are entered whenever the Power
Save (0x81 hexadecimal) command is issued to the
serial port. The particular power save mode entered
depends on state of bit D4 (the power save select
bit) in the configuration register. If D4 is logic 0,
the converter enters the standby mode reducing the
power consumption to 1 mW. The standby mode
leaves the oscillator and the on-chip bias generator
Configuration Register:
000040(H)
Offset Register:
000000(H)
Gain Register:
400000(H)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1F-EY | CONVERTER MOD DC/DC 72V 50W |
| GCM22DSXH | CONN EDGECARD 44POS DIP .156 SLD |
| CDB5368 | BOARD EVAL FOR CS5368 192KHZ ADC |
| VE-J1B-EY | CONVERTER MOD DC/DC 95V 50W |
| VE-J14-EY | CONVERTER MOD DC/DC 48V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB5530U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24-Bit 1-Ch Low-Noise ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| CDB5532U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| CDB5534U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| CDB5534U-Z | 功能描述:EVAL BD 24-BIT ADCS W/ULTRALN PG 制造商:cirrus logic inc. 系列:- 零件狀態:在售 A/D 轉換器數:1 位數:24 采樣率（每秒）:3.84k 數據接口:串行 輸入范圍:±2.5 V 不同條件下的功率（典型值）:35mW @ 3.84kSPS 使用的 IC/零件:CS5534 所含物品:板，電纜 標準包裝:1 |
| CDB5540 | 制造商:Cirrus Logic 功能描述:EVAL BOARD FOR CS5540 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。