- 您現在的位置：買賣IC網 > PDF目錄295215 > CAT28F001PI-12B (ON SEMICONDUCTOR) 128K X 8 FLASH 12V PROM, 120 ns, PDIP32 PDF資料下載
參數資料
| 型號： | CAT28F001PI-12B |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | PROM |
| 英文描述： | 128K X 8 FLASH 12V PROM, 120 ns, PDIP32 |
| 封裝： | PLASTIC, DIP-32 |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 111K |
| 代理商： | CAT28F001PI-12B |
CAT28F001
11
Doc. No. MD-1078, Rev. K
2008 SCILLC. All rights reserved.
Characteristics subject to change without notice
Bus
Operation
Command
Comments
Write
Program
Data = 40H
Setup
Address = Bytes to be Programmed
Write
Program
Data to be programmed
Address = Byte to be Programmed
Read
Status Register Data.
Toggle OE or CE to update
Status Register
Check SR.7
Standby
1 = Ready, 0 = Busy
Repeat for subsequent bytes.
Full Status check can be done after each byte or after a sequence
of bytes.
Write FFH after the last byte programming operation to reset the
device to Read Array Mode.
Bus
Operation
Command
Comments
Standby
Check SR.3
1 = VPP Low Detect
Standby
Check SR.3
1 = Byte Program Error
SR.3 MUST be cleared, if set during a program attempt, before
further attempts are allowed by the Write State Machine.
SR.3 is only cleared by the Clear Status Register Command, in
case where multiple bytes are programmed before full status is
checked.
If error is detected, clear the Status Register before attempting retry
or other error recovery.
START
WRITE 40H,
BYTE ADDRESS
READ STATUS
REGISTER
SR.7 = 1?
FULL STATUS
CHECK IF DESIRED
BYTE PROGRAM
COMPLETED
STATUS REGISTER DATA
READ (SEE ABOVE)
SR.3 = 0?
SR.4 = 0?
BYTE PROGRAM
SUCCESSFUL
NO
WRITE BYTE
ADDRESS/DATA
FULL STATUS CHECK PROCEDURE
NO
VPP RANGE
ERROR
BYTE PROGRAM
ERROR
YES
Figure 4 Byte Programming Flowchart
IN-SYSTEM OPERATION
For on-board programming, the RP pin is the most
convenient means of altering the boot block. Before
issuing Program or Erase confirms commands, RP must
transition to VHH. Hold RP at this high voltage throughout
the program or erase interval (until after Status Register
confirm of successful completion). At this time, it can
return to VIH or VIL.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT28F010T-90 | 128K X 8 FLASH 12V PROM, 90 ns, PDSO32 |
| CAT28F102NA-12T | 64K X 16 FLASH 12V PROM, 120 ns, PQCC44 |
| CAT28LV64H-25TE13 | 8K X 8 EEPROM 3V, 250 ns, PDSO32 |
| CAT28LV64JI-35TE13 | 8K X 8 EEPROM 3V, 350 ns, PDSO28 |
| CAT28LV64T-30TE13 | 8K X 8 EEPROM 3V, 300 ns, PDSO32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT28F001PI-12T | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F001PI-90B | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F001PI-90T | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F001T-12B | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| CAT28F001T-12T | 功能描述:閃存 (128x8) 1M RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。