參數資料
型號： ATTINY13
廠商： Atmel Corp.
元件分類： 8位微控制器
英文描述： -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
中文描述： 位AVR微控制器具有8K字節的系統內可編程閃存
文件頁數： 95/176頁
文件大?。?/td> 2962K
代理商： ATTINY13
25
2535J–AVR–08/10
ATtiny13
When this clock source is selected, start-up times are determined by the SUT fuses as shown in
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in Reset during such changes in the clock frequency.
Note that the System Clock Prescaler can be used to implement run-time changes of the internal
clock frequency while still ensuring stable operation. Refer to “System Clock Prescaler” on page
26 for details.
6.2.2
Calibrated Internal 4.8/9.6 MHz Oscillator
The calibrated internal oscillator provides a 4.8 or 9.6 MHz clock source. The frequency is nomi-
nal at 3V and 25
°C. If the frequency exceeds the specification of the device (depends on V
CC),
the CKDIV8 fuse must be programmed so that the internal clock is divided by 8 during start-up.
The internal oscillator is selected as the system clock by programming the CKSEL fuses as
shown in Table 6-4. If selected, it will operate with no external components.
Note:
1. The device is shipped with this option selected.
During reset, hardware loads the calibration data into the OSCCAL register and thereby auto-
matically calibrates the oscillator. There are separate calibration bytes for 4.8 and 9.6 MHz
operation but only one is automatically loaded during reset (see section “Calibration Bytes” on
page 104). This is because the only difference between 4.8 MHz and 9.6 MHz mode is an inter-
nal clock divider.
By changing the OSCCAL register from SW, see “OSCCAL – Oscillator Calibration Register” on
page 27, it is possible to get a higher calibration accuracy than by using the factory calibration.
When this oscillator is used as the chip clock, the Watchdog Oscillator will still be used for the
Watchdog Timer and for the Reset Time-out. For more information on the pre-programmed cali-
bration value, see the section “Calibration Bytes” on page 104.
Table 6-3.
Start-up Times for the External Clock Selection
SUT1..0
Start-up Time from
Power-down and Power-save
Additional Delay
from Reset
Recommended
Usage
00
6 CK
14CK
BOD enabled
01
6 CK
14CK + 4 ms
Fast rising power
10
6 CK
14CK + 64 ms
Slowly rising power
11
Reserved
Table 6-4.
Internal Calibrated RC Oscillator Operating Modes
CKSEL1..0
Nominal Frequency
10(1)
9.6 MHz
01
4.8 MHz
相關PDF資料
PDF描述
AT93C56AY1-10YI-1.8 3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16)
AT93C56AY1-10YI-2.7 Circular Connector; No. of Contacts:4; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:22; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:22-10 RoHS Compliant: No
AT93C56A-10SU-2.7 24 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
AT93C56A-10TU-1.8 240 x 128 pixel format, CFL Backlight with power harness
AT17LV128A-10BJC FPGA Configuration EEPROM Memory
相關代理商/技術參數
參數描述
ATTINY13_08 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13_10 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13-10SU 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13-12PI 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13-12PJ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*