參數資料
型號： ATTINY13
廠商： Atmel Corp.
元件分類： 8位微控制器
英文描述： -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
中文描述： 位AVR微控制器具有8K字節的系統內可編程閃存
文件頁數： 3/176頁
文件大?。?/td> 2962K
代理商： ATTINY13
100
2535J–AVR–08/10
ATtiny13
To read the Fuse High Byte (FHB), simply replace the address in the Z-pointer with 0x0003 and
repeat the procedure above.
If successful, the contents of the destination register are as follows.
for more information on fuse and lock bits.
16.7 Preventing Flash Corruption
During periods of low VCC, the Flash program can be corrupted because the supply voltage is
too low for the CPU and the Flash to operate properly. These issues are the same as for board
level systems using the Flash, and the same design solutions should be applied.
A Flash program corruption can be caused by two situations when the voltage is too low. First, a
regular write sequence to the Flash requires a minimum voltage to operate correctly. Secondly,
the CPU itself can execute instructions incorrectly, if the supply voltage for executing instructions
is too low.
Flash corruption can easily be avoided by following these design recommendations (one is
sufficient):
1. Keep the AVR RESET active (low) during periods of insufficient power supply voltage.
This can be done by enabling the internal Brown-out Detector (BOD) if the operating
voltage matches the detection level. If not, an external low VCC reset protection circuit
can be used. If a reset occurs while a write operation is in progress, the write operation
will be completed provided that the power supply voltage is sufficient.
2. Keep the AVR core in Power-down sleep mode during periods of low VCC. This will pre-
vent the CPU from attempting to decode and execute instructions, effectively protecting
the SPMCSR Register and thus the Flash from unintentional writes.
16.8 Programming Time for Flash when Using SPM
The calibrated RC Oscillator is used to time Flash accesses. Table 16-1 on page 100 shows the
typical programming time for Flash accesses from the CPU.
Note:
1. The min and max programming times is per individual operation.
Bit
7
6
543
2
1
0
Rd
FHB7
FHB6
FHB5
FHB4
FHB3
FHB2
FHB1
FHB0
Table 16-1.
SPM Programming Time(1)
Symbol
Min Programming Time
Max Programming Time
Flash write (Page Erase, Page Write, and
write lock bits by SPM)
3.7 ms
4.5 ms
相關PDF資料
PDF描述
AT93C56AY1-10YI-1.8 3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16)
AT93C56AY1-10YI-2.7 Circular Connector; No. of Contacts:4; Series:; Body Material:Aluminum Alloy; Connecting Termination:Solder; Connector Shell Size:22; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:22-10 RoHS Compliant: No
AT93C56A-10SU-2.7 24 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
AT93C56A-10TU-1.8 240 x 128 pixel format, CFL Backlight with power harness
AT17LV128A-10BJC FPGA Configuration EEPROM Memory
相關代理商/技術參數
參數描述
ATTINY13_08 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13_10 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13-10SU 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13-12PI 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash
ATTINY13-12PJ 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*