參數資料
型號： AT45CS1282
廠商： Atmel Corp.
英文描述： 128-megabit 2.7-volt Dual-interface Code Shadow DataFlash
中文描述： 128兆2.7伏的雙界面代碼陰影的DataFlash
文件頁數： 5/33頁
文件大?。?/td> 252K
代理商： AT45CS1282
5
AT45CS1282 [Preliminary]
3447A–DFLSH–2/04
Program and Erase Commands
BUFFER WRITE:
Data can be clocked in from the input pins (SI or I/O7 - I/O0) into
either buffer 1 or buffer 2. To load data into either buffer, a 1-byte opcode, 84H for buffer
1 or 87H for buffer 2, must be clocked into the device, followed by four address bytes
comprised of 21 don’t care bits and 11 buffer address bits (BFA10 - BFA0). The 11
buffer address bits specify the first byte in the buffer to be written. After the last address
byte has been clocked into the device, data can then be clocked in on subsequent clock
cycles. If the end of the data buffer is reached, the device will wrap around back to the
beginning of the buffer. Data will continue to be loaded into the buffer until a low-to-high
transition is detected on the CS pin.
BUFFER TO MAIN MEMORY PAGE PROGRAM:
A previously-erased page within main
memory can be programmed with the contents of either buffer 1 or buffer 2. The pro-
gramming time is selectable by the system through the use of different opcodes
between a normal mode and a fast mode (the fast program option will consume more
current). A 1-byte opcode, 88H for buffer 1 or 89H for buffer 2 (98H for buffer 1 fast pro-
gram or 99H for buffer 2 fast program), must be clocked into the device followed by four
address bytes consisting of 7 don’t care bits, 14-page address bits (PA13 - PA0) that
specify the page in the main memory to be written and 11 don’t care bits. When a low-to-
high transition occurs on the CS pin, the part will program the data stored in the buffer
into the specified page in the main memory. It is necessary that the page in main mem-
ory that is being programmed has been previously erased using the sector erase
commands. The programming of the page is internally self-timed and should take place
in a maximum time of t
P
for normal programming or t
FP
for fast programming. During this
time, the status register and the RDY/BUSY pin will indicate that the part is busy.
SECTOR ERASE:
The Sector Erase command can be used to individually erase any
sector in the main memory. There are 65 sectors and only one sector can be erased at
one time. Sector 0a requires a different opcode than sectors 0b-63. To perform a sector
0a erase, an opcode of 50h must be loaded into the device, followed by four address
bytes comprised of 7 don’t care bits, 11-page address bits (PA13 - PA3) and 14 don’t
care bits. To perform a sector 0b-63 erase, an opcode of 7Ch must be loaded into the
device, followed by four address bytes comprised of 7 don’t care bits, 6-page address
bits (PA13 - PA8) and 19 don’t care bits. The 6-page address bits are used to specify
which sector is to be erased. Refer to Sector Erase addressing table. When a low-to-
high transition occurs on the CS pin, the part will erase the selected sector. The erase
operation is internally self-timed and should take place in a maximum time of t
SE
. During
this time, the status register and the RDY/BUSY pin will indicate that the part is busy.
相關PDF資料
PDF描述
AT45D011 1-Megabit 5.0-volt Only Serial DataFlash
AT45D011-JC 1-Megabit 5.0-volt Only Serial DataFlash
AT45D011-JI 1-Megabit 5.0-volt Only Serial DataFlash
AT45D011-SC 1-Megabit 5.0-volt Only Serial DataFlash
AT45D011-SI 1-Megabit 5.0-volt Only Serial DataFlash
相關代理商/技術參數
參數描述
AT45CS1282-TC 功能描述:閃存 128M bit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
AT45CS1282-TI 功能描述:IC FLASH 128MBIT 50MHZ 40TSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤
AT45D011 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:1-Megabit 5.0-volt Only Serial DataFlash
AT45D011-JC 功能描述:閃存 1M bit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
AT45D011-JI 功能描述:閃存 1M bit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*