參數資料
型號： AT32UC3A3256AU-ALUT
廠商： Atmel
文件頁數： 25/94頁
文件大?。?/td> 0K
描述： IC MCU 256KB FLASH 144LQFP
產品培訓模塊： AVR® UC3 Introduction
標準包裝： 300
系列： AVR®32 UC3 A3 Audio
核心處理器： AVR
芯體尺寸： 32-位
速度： 66MHz
連通性： EBI/EMI，I²C，IrDA，MMC，SPI，SSC，UART/USART，USB OTG
外圍設備： 欠壓檢測/復位，DMA，POR，WDT
輸入/輸出數： 110
程序存儲器容量： 256KB（256K x 8）
程序存儲器類型： 閃存
RAM 容量： 128K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 144-LQFP
包裝： 托盤
31
32072SH–AVR32–10/2012
AT32UC3A3
The user must also make sure that the system stack is large enough so that any event is able to
push the required registers to stack. If the system stack is full, and an event occurs, the system
will enter an UNDEFINED state.
4.5.2
Exceptions and Interrupt Requests
When an event other than scall or debug request is received by the core, the following actions
are performed atomically:
1.
The pending event will not be accepted if it is masked. The I3M, I2M, I1M, I0M, EM, and
GM bits in the Status Register are used to mask different events. Not all events can be
masked. A few critical events (NMI, Unrecoverable Exception, TLB Multiple Hit, and
Bus Error) can not be masked. When an event is accepted, hardware automatically
sets the mask bits corresponding to all sources with equal or lower priority. This inhibits
acceptance of other events of the same or lower priority, except for the critical events
listed above. Software may choose to clear some or all of these bits after saving the
necessary state if other priority schemes are desired. It is the event source’s respons-
ability to ensure that their events are left pending until accepted by the CPU.
2.
When a request is accepted, the Status Register and Program Counter of the current
context is stored to the system stack. If the event is an INT0, INT1, INT2, or INT3, reg-
isters R8-R12 and LR are also automatically stored to stack. Storing the Status
Register ensures that the core is returned to the previous execution mode when the
current event handling is completed. When exceptions occur, both the EM and GM bits
are set, and the application may manually enable nested exceptions if desired by clear-
ing the appropriate bit. Each exception handler has a dedicated handler address, and
this address uniquely identifies the exception source.
3.
The Mode bits are set to reflect the priority of the accepted event, and the correct regis-
ter file bank is selected. The address of the event handler, as shown in Table 4-4, is
loaded into the Program Counter.
The execution of the event handler routine then continues from the effective address calculated.
The rete instruction signals the end of the event. When encountered, the Return Status Register
and Return Address Register are popped from the system stack and restored to the Status Reg-
ister and Program Counter. If the rete instruction returns from INT0, INT1, INT2, or INT3,
registers R8-R12 and LR are also popped from the system stack. The restored Status Register
contains information allowing the core to resume operation in the previous execution mode. This
concludes the event handling.
4.5.3
Supervisor Calls
The AVR32 instruction set provides a supervisor mode call instruction. The scall instruction is
designed so that privileged routines can be called from any context. This facilitates sharing of
code between different execution modes. The scall mechanism is designed so that a minimal
execution cycle overhead is experienced when performing supervisor routine calls from time-
critical event handlers.
The scall instruction behaves differently depending on which mode it is called from. The behav-
iour is detailed in the instruction set reference. In order to allow the scall routine to return to the
correct context, a return from supervisor call instruction, rets, is implemented. In the AVR32UC
CPU, scall and rets uses the system stack to store the return address and the status register.
4.5.4
Debug Requests
The AVR32 architecture defines a dedicated Debug mode. When a debug request is received by
the core, Debug mode is entered. Entry into Debug mode can be masked by the DM bit in the
相關PDF資料
PDF描述
AT91SAM7SE512-AU IC ARM7 MCU FLASH 512K 128-LQFP
AT32AP7002-CTUT IC MCU 32BIT AVR32 196-CBGA
VE-B33-IY-F2 CONVERTER MOD DC/DC 24V 50W
VE-B33-CU-B1 CONVERTER MOD DC/DC 24V 200W
AT32UC3C0512C-ALUT IC MCU AVR32 512K FLASH 144LQFP
相關代理商/技術參數
參數描述
AT32UC3A3256-CTUR 功能描述:32位微控制器 - MCU 256KB, 144FFBGA Ind RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
AT32UC3A3256-CTUT 功能描述:32位微控制器 - MCU 256KB, 144FFBGA Ind RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
AT32UC3A3256-CTUT SL383 制造商:Atmel Corporation 功能描述:
AT32UC3A3256-DDW 功能描述:32位微控制器 - MCU UC3A3 256Kb flash - 256Kflash UC3A - Wafer RoHS:否 制造商:Texas Instruments 核心:C28x 處理器系列:TMS320F28x 數據總線寬度:32 bit 最大時鐘頻率:90 MHz 程序存儲器大小:64 KB 數據 RAM 大小:26 KB 片上 ADC:Yes 工作電源電壓:2.97 V to 3.63 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:LQFP-80 安裝風格:SMD/SMT
AT32UC3A3256S 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:32-bit AVR? Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*