- 您現在的位置：買賣IC網 > PDF目錄381419 > AT25320 (Atmel Corp.) 32K SPI Serial EEPROMs(32K SPI串行EEPROM) PDF資料下載
參數資料
| 型號： | AT25320 |
| 廠商： | Atmel Corp. |
| 英文描述： | 32K SPI Serial EEPROMs(32K SPI串行EEPROM) |
| 中文描述： | 32K的的SPI（32K的的SPI串行EEPROM的串行EEPROM） |
| 文件頁數： | 8/17頁 |
| 文件大?。?/td> | 250K |
| 代理商： | AT25320 |
AT25080/160/320/640
8
The WRSR instruction also allows the user to enable or
disable the write protect (WP) pin through the use of the
Write Protect Enable (WPEN) bit. Hardware write protec-
tion is enabled when the WP pin is low and the WPEN bit is
“
1
”
. Hardware write protection is disabled when either the
WP pin is high or the WPEN bit is
“
0
”
. When the device is
hardware write protected, writes to the Status Register,
including the Block Protect bits and the WPEN bit, and the
block-protected sections in the memory array are disabled.
Writes are only allowed to sections of the memory which
are not block-protected.
NOTE:
When the WPEN bit is hardware write protected, it
cannot be changed back to
“
0
”
, as long as the WP pin is
held low.
READ
AT25080/160/320/640 via the SO (Serial Output) pin
requires the following sequence. After the CS line is pulled
low to select a device, the READ op-code is transmitted via
the SI line followed by the byte address to be read
(A15 - A0, Refer to Table 6). Upon completion, any data on
the SI line will be ignored. The data (D7 - D0) at the speci-
fied address is then shifted out onto the SO line. If only one
byte is to be read, the CS line should be driven high after
the data comes out. The READ sequence can be continued
since the byte address is automatically incremented and
data will continue to be shifted out. When the highest
address is reached, the address counter will roll over to the
lowest address allowing the entire memory to be read in
one continuous READ cycle.
SEQUENCE
(READ):
Reading
the
WRITE SEQUENCE (WRITE):
In order to program the
AT25080/160/320/640, two separate instructions must be
executed. First, the device
must be write enabled
via the
Write Enable (WREN) Instruction. Then a Write (WRITE)
Instruction may be executed. Also, the address of the
memory location(s) to be programmed must be outside the
protected address field location selected by the Block Write
Protection Level. During an internal write cycle, all com-
mands will be ignored except the RDSR instruction.
A Write Instruction requires the following sequence. After
the CS line is pulled low to select the device, the WRITE
op-code is transmitted via the SI line followed by the byte
address (A15 - A0) and the data (D7 - D0) to be pro-
grammed (Refer to Table 6). Programming will start after
the CS pin is brought high. (The LOW-to-High transition of
the CS pin must occur during the SCK low-time immedi-
ately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined
by initiating a READ STATUS REGISTER (RDSR) Instruc-
tion. If Bit 0 = 1, the WRITE cycle is still in progress. If Bit 0
= 0, the WRITE cycle has ended. Only the READ STATUS
REGISTER instruction is enabled during the WRITE pro-
gramming cycle.
The AT25080/160/320/640 is capable of a 32-byte PAGE
WRITE operation. After each byte of data is received, the
five low order address bits are internally incremented by
one; the high order bits of the address will remain constant.
If more than 32 bytes of data are transmitted, the address
counter will roll over and the previously written data will be
overwritten. The AT25080/160/320/640 is automatically
returned to the write disable state at the completion of a
WRITE cycle.
NOTE:
If the device is not Write enabled (WREN), the
device will ignore the Write instruction and will return to the
standby state, when CS is brought high. A new CS falling
edge is required to re-initiate the serial communication.
Table 5.
WPEN Operation
WPEN
WP
WEN
Protected
Blocks
Unprotected
Blocks
Status
Register
0
X
0
Protected
Protected
Protected
0
X
1
Protected
Writable
Writable
1
Low
0
Protected
Protected
Protected
1
Low
1
Protected
Writable
Protected
X
High
0
Protected
Protected
Protected
X
High
1
Protected
Writable
Writable
Table 6.
Address Key
Address
AT25080
AT25160
AT25320
AT25640
A
N
A
9
- A
0
A
10
- A
0
A
11
- A
0
A
12
- A
0
Don
’
t
Care Bits
A
15
- A
10
A
15
- A
11
A
15
- A
12
A
15
- A
13
相關PDF資料 |
PDF描述 |
|---|---|
| AT25F1024AN-10SU-2.7 | SPI Serial Memory |
| AT25F1024AY4-10YU-2.7 | SPI Serial Memory |
| AT25F1024A | High Speed CMOS Logic Hex Buffers/Line Drivers with Inverting 3-State Outputs 16-PDIP -55 to 125 |
| AT25F1024 | High Speed CMOS Logic Hex Buffers/Line Drivers with Non-Inverting 3-State Outputs 16-SOIC -55 to 125 |
| AT25F512 | SPI Serial Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25320-10PA-2.7C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|4KX8|CMOS|DIP|8PIN|PLASTIC |
| AT25320-10PA-5.0C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SERIAL EEPROM|4KX8|CMOS|DIP|8PIN|PLASTIC |
| AT25320-10PC | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25320-10PC-1.8 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25320-10PC-2.7 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
發布緊急采購，3分鐘左右您將得到回復。