- 您現在的位置：買賣IC網 > PDF目錄381413 > AT24RF08C (Atmel Corp.) Asset Identification EEPROM(雙存取EEPROM（帶一個有線串行端口和一個無線RFID端口）) PDF資料下載
參數資料
| 型號： | AT24RF08C |
| 廠商： | Atmel Corp. |
| 英文描述： | Asset Identification EEPROM(雙存取EEPROM（帶一個有線串行端口和一個無線RFID端口）) |
| 中文描述： | 資產識別的EEPROM（雙存取的EEPROM（帶一個有線串行端口和一個無線RFID的端口）） |
| 文件頁數： | 5/21頁 |
| 文件大?。?/td> | 429K |
| 代理商： | AT24RF08C |
AT24RF08C
5
Access Protection Page
The serial port may be used to read and write the Access
Protection Page (APP) and ID Page using device access
codes of B8 and B9 (hex) instead of the normal value of A8
through AF (hex) that are used to access the rest of the
EEPROM memory. The second byte of write commands
(the word address) should be in the range of 00 through 0f
(hex) for the APP page and 10 through 1F (hex) for the ID
page. This coding is shown below.
Reads and writes to these two pages may take place on a
single byte basis only. Multi-byte operations will be
NACK
’
ed.
As an example, the bit encoding for a single byte read and
write command are shown below.
The AT24RF08C will acknowledge all device addresses of
B8 or B9 (hex). If the most significant three bits of the word
address are not all 0 (indicating an address outside the
Access Protection and ID pages), the chip will NACK the
access.
Bytes 0 through 7 of the APP contain 8 identical sets of
access control fields (PBx, RFx, TWx and SBx) for each of
the eight blocks of memory on the chip, which operate
according to the table listed in the Access Protection sec-
tion above. When the sticky bit in one of these bytes is set,
that byte can be written by the system. Once a sticky bit is
reset (written to zero) by the software, the byte containing it
can no longer be modified by the software until the next
power cycle. These bytes can always be read by the sys-
tem.
Byte 8 contains another PB field (PB
AP
) as bits 0 and 1 and
an additional sticky bit (SB
AP
) as bit 7. The value of the
PB
AP
bits controls read and write access to the last 7 bytes
(#9-15) of the APP and all 16 bytes of the ID page
according to the encoding listed in the
“
Access Protection
”
section above. The value of the PB
AP
bits can only be
changed (via writes from the serial port) when SB
AP
is high.
This byte can always be read by the system. Bits 0 through
6 of this byte are stored in EEPROM memory and do not
change when the power is cycled or the PROT pin changes
state.
Byte 9 contains the 8 block 0 write protection bits (WP) for
each page within block 0.
Byte 10 is the tamper byte, and the LSB of this byte can be
used to determine if the
“
set tamper
”
command had been
executed from the RFID port. This bit can be reset in
software via the serial port by writing a 0 to it.
Byte 10 also contains the coil detection control. This
feature is intended to permit the system to determine if a
coil is connected to the pins. It works by driving a small
current through the coil pins and determining if there is a
low resistance between them. The coil resistance must be
less than R
COIL
for the coil to be properly detected. To
enable this, the Detect Enable (DE) bit should be set to a 1.
After a delay of at least 200 μs, the Detect Coil (DC) bit is
then read and a
“
1
”
indicates that a coil is present.
Note that the RFID interface may not function properly
when the DE bit is set to a 1, and so the software should
ensure that it is always written to a 0 when the coil
detection sequence has completed. The DE bit is
automatically reset to a 0 upon power-up or when PROT is
held low, but is not timed out internally by the device.
When the DE bit is low, the value of the DC bit will default
to a high state. This does
not
indicate the presence of a
coil, as the state of the DC bit is only valid when the DE bit
is high.
Bytes 11 through 14 are currently reserved and should not
be used by the system. Byte 14 may not be written by the
device (via either interface) at any time.
Access Protection Page Examples
For Write Operations:
1 0 1 1 1 0 0 0
0 0 0 A
4
A
3
A
2
A
1
A
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
For Read Operations:
1 0 1 1 1 0 0 1
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
相關PDF資料 |
PDF描述 |
|---|---|
| AT24RF08 | 1K x 8 Dual Access EEPROM with RFID and Serial Interfaces |
| AT25010-10PI-1.8 | SPI Serial EEPROMs |
| AT25020-10PI-1.8 | SPI Serial EEPROMs |
| AT25040-10PI-1.8 | SPI Serial EEPROMs |
| AT25040N-10SC-1.8 | SPI Serial EEPROMs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24RF08CN-105C | 功能描述:IC EEPROM 8KBIT 100KHZ 8SOIC 制造商:microchip technology 系列:- 包裝:管件 零件狀態:停產 存儲器類型:非易失 存儲器格式:EEPROM 技術:EEPROM 存儲容量:8Kb （1K x 8） 時鐘頻率:100kHz 寫周期時間 - 字，頁:10ms 訪問時間:450ns 存儲器接口:I2C 電壓 - 電源:2.4 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TJ） 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 基本零件編號:AT24RF08 標準包裝:1 |
| AT24RF08CN-10SC | 功能描述:電可擦除可編程只讀存儲器 RFID 8k RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24RF08CN10SC-C0006 | 制造商:Atmel Corporation 功能描述:EEPROM |
| AT24RF08CT-10T1C | 制造商:Atmel Corporation 功能描述:1K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO14 |
| AT24RF08-EK | 功能描述:KIT EVAL FOR AT24RF08CN-10SC RoHS:否 類別:RF/IF 和 RFID >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:用于 200/300 系列的歐盟開發套件 適用于相關產品:Zensys RF 模塊 所含物品:開發板，模塊，編程器，軟件，線纜，電源 其它名稱:703-1019Q3225667 |
發布緊急采購，3分鐘左右您將得到回復。