- 您現在的位置：買賣IC網 > PDF目錄381405 > AT24C128-W2.7-11 (ATMEL CORP) Two-wire Serial EEPROMs PDF資料下載
參數資料
| 型號： | AT24C128-W2.7-11 |
| 廠商： | ATMEL CORP |
| 元件分類： | DRAM |
| 英文描述： | Two-wire Serial EEPROMs |
| 中文描述： | 16K X 8 I2C/2-WIRE SERIAL EEPROM, UUC |
| 封裝： | DIE |
| 文件頁數： | 7/23頁 |
| 文件大?。?/td> | 388K |
| 代理商： | AT24C128-W2.7-11 |
7
AT24C128/256
0670S–SEEPR–5/06
Device
Operation
CLOCK and DATA TRANSITIONS:
The SDA pin is normally pulled high with an external
device. Data on the SDA pin may change only during SCL low time periods (see Figure 4 on
page 8). Data changes during SCL high periods will indicate a start or stop condition as
defined below.
START CONDITION:
A high-to-low transition of SDA with SCL high is a start condition which
must precede any other command (see Figure 5 on page 9).
STOP CONDITION:
A low-to-high transition of SDA with SCL high is a stop condition. After a
read sequence, the stop command will place the EEPROM in a standby power mode (see Fig-
ure 5 on page 9).
ACKNOWLEDGE:
All addresses and data words are serially transmitted to and from the
EEPROM in 8-bit words. The EEPROM sends a zero during the ninth clock cycle to acknowl-
edge that it has received each word.
STANDBY MODE:
The AT24C128/256 features a low power standby mode which is enabled:
a) upon power-up and b) after the receipt of the STOP bit and the completion of any internal
operations.
MEMORY RESET:
After an interruption in protocol, power loss or system reset, any two-wire
part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in
each cycle while SCL is high and then (c) create a start condition as SDA is high.
相關PDF資料 |
PDF描述 |
|---|---|
| AT24C128Y1-10YU-1.8 | Two-wire Serial EEPROMs |
| AT24C128Y4-10YU-1.8 | Two-wire Serial EEPROMs |
| AT24C128B | Two-wire Serial EEPROM |
| AT24C128 | 128K 2-wire Serial EEPROMs(128K 2線串行EEPROM) |
| AT24C164-10PU-1.8 | Two-Wire Serial EEPROM 16K (2048 x 8) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT24C128WSC | 制造商:Atmel Corporation 功能描述: |
| AT24C128Y1-10YI | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:2-wire Serial EEPROMs |
| AT24C128Y1-10YI-1.8 | 功能描述:IC EEPROM 128KBIT 400KHZ 8MAP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT24C128Y1-10YI-2.7 | 功能描述:電可擦除可編程只讀存儲器 128/256K 2-Wire Bus RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT24C128Y1-10YU-1.8 | 功能描述:IC EEPROM 128KBIT 400KHZ 8MAP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:RAM 存儲器類型:SDRAM 存儲容量:256M（8Mx32） 速度:143MHz 接口:并聯 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:90-VFBGA 供應商設備封裝:90-VFBGA（8x13） 包裝:托盤 其它名稱:Q2841869 |
發布緊急采購，3分鐘左右您將得到回復。